NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual M6 – 421
Doc. No. 8201 - Release 1.0
July 2003
PS AUTHORIZATION
The D
term Drover user can confirm the identity to prevent an unauthorized
Dterm Drover from accessing the system.  Identity is confirmed between the
system and Dterm Drover by checking the unique key information of the
Dterm Drover.
PS LOCATION REGISTRATION
The system can supervise the location of each D
term Drover and allow call
termination after receiving the...

July 2003 NEC Business Solutions Ltd
422 – M6Multi-Zone Digital Cordless
Doc. No. 8201 - Release 1.0
July 2003
If the PHS phone is set with CFA, all calls go immediately to the
Personal VM Greeting Message.
	A maximum of four PS handsets should be programmed with the same
Call Arrival Key (CAR). A maximum of four PS handsets within the
same Call Area will ring simultaneously when receiving incoming
outside calls on CAR keys.
General
	Maximum allowable placement.
	Each base station provides 3 voice...

Xen IPK Features and Specifications Manual
Features and Specifications Manual M6 – 423
Doc. No. 8201 - Release 1.0
July 2003
	Either a Line Key or Call Appearance Key (CAP key) must be
programmed for each PS handset port to enable line seizure and to
allow DIT, DID and transferred CO calls to be answered.
GUIDE TO 
FEATURE 
PROGRAMMING
Table A6-1:  Specifications for BS/PS
Cell Station Personal Station
ItemSpecificationItemSpecification
No of voice channels 
per BSMaximum 3 Frequency 1.895 ~ 1.918 GHz...

July 2003 NEC Business Solutions Ltd
424 – M6Multi-Zone Digital Cordless
Doc. No. 8201 - Release 1.0
July 2003
¶ + BTTStation to Class of Service Feature 
Assignment4-17
¶ + BTM Ringing Line Preference Selection 4-11
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key 

Features and Specifications Manual M7 – 425
Doc. No. 8201 - Release 1.0
July 2003
Music on HoldM-7
FEATURE 
DESCRIPTIONA locally provided music source or an internal music source can be used to
supply music to parties on hold, to assure them that they are still connected
to the system.
CO ports can also be used to provide multiple music sources to different
COs in the system.
SYSTEM 
AVAILABILITYTerminal Type
Not applicable.
Required Components
External source connected to the RCA jack on the basic...

July 2003 NEC Business Solutions Ltd
426 – M7Music on Hold
Doc. No. 8201 - Release 1.0
July 2003
	When connecting an external music source to a spare port of a COI( )-
U( ) ETU or COID( )-U( ) ETU, a powered line isolation unit with a
telecommunications compliance label is required to provide
line voltage into the port. For example, Batesford Electronics Model
No. TIC2F2.
General
	Music On Hold (MOH) is provided for all outside and internal calls
on hold.
	Music On Hold can be disabled if required....

Xen IPK Features and Specifications Manual
Features and Specifications Manual M7 – 427
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶ + AUAutomated Attendant Delay Announcement 
Hold Tone section1-4-17
¶ + BCSMusic on Hold Pattern Selection1-8-09
¶ + BCSHold Tone Source Assignment1-8-31
¶ + BCSHold Internal Tone Volume Selection1-8-32
¶ + BCTCO External Source...

July 2003 NEC Business Solutions Ltd
428 – M7Music on Hold
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual N1 – 431
Doc. No. 8201 - Release 1.0
July 2003
DRAFT 3
Nesting DialN-1
FEATURE 
DESCRIPTIONMultiline Terminal users may store up to four Speed Dial (System or Station
Speed Dial) buffer numbers in one Station Speed Dial buffer. All four buffers
can then be consecutively dialled by pressing the Redial key and dialling a
single Station Speed Dial buffer number. 
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals.
Required Components
None.
OPERATING 
PROCEDURES
1....

July 2003 NEC Business Solutions Ltd
432 – N1Nesting Dial
Doc. No. 8201 - Release 1.0
July 2003
1. PressT.
2. Press
Q.
3. Press the Feature Access key.
4. Dial (Function) code
0.
5. Dial the Trunk or Trunk Group Access Code (maximum four digits).
6. Press
O.
7. Dial the Speed Dial buffer number to be nested (
00~II).
8. Repeat steps 6 and 7 up to three times if required.
9. Press
U, and enter a name using the Character Codes (optional
step).
10. Press
T.
1. Press
T.
2. Press
Q.
3. Press the One-Touch...