Home > NEC > Communications System > NEC Xen Ipk Features And Specifications Manual

NEC Xen Ipk Features And Specifications Manual

Here you can view all the pages of manual NEC Xen Ipk Features And Specifications Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 461

Features and Specifications Manual P2 – 453
Doc. No. 8201 - Release 1.0
July 2003
PC ProgrammingP-2
FEATURE 
DESCRIPTIONThe MIFM-U( ) ETU and Maintenance Access Terminal (MAT) software
allows the system to be programmed from a personal computer (PC).
System Data can be transferred to/from a diskette for backup of system
data. MAT PC programming software also allows the user to print station
designation strips to shorten installation time. End users can use the
Customer Administration Terminal (CAT) PC...

Page 462

July 2003 NEC Business Solutions Ltd
454 – P2PC Programming
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BSCard Interface Slot Assignment 7-1
¶+BSMIF (SMDR) Assignment 7-3-02
¶+BSMIF (LCR) Assignment 7-3-01
¶+CSSCOM Port Parity/Stop Bit Setting Assignment 1-8-36
¶+CSSCOM Port Baud Rate Setting Assignment 1-8-35
¶+CSSModem Port for Remote Programming...

Page 463

Features and Specifications Manual P3 – 455
Doc. No. 8201 - Release 1.0
July 2003
Pooled Line (Outgoing)P-3
FEATURE 
DESCRIPTIONThe Pooled Line feature allows Multiline Terminal users to seize an outside
line on one Pooled line key. One Pooled line key can accommodate a Trunk
group or Route Advance Block.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. Press the Pooled line key, and receive outside line dial tone.
2. Dial the desired telephone...

Page 464

July 2003 NEC Business Solutions Ltd
456 – P3Pooled Line (Outgoing)
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BCTTrunk-to-Trunk Group Assignment 3-03
¶+BTM4Line Key Selection for Telephone Mode4-12
¶+BNLine Key Selection 2-05
¶+BNLine Key Selection for Tenant Mode 2-06
4When the system is at default this Memory Block must be programmed for the feature to be...

Page 465

Features and Specifications Manual P4 – 457
Doc. No. 8201 - Release 1.0
July 2003
Power Failure TransferP-4
FEATURE 
DESCRIPTIONThe Power Failure Transfer feature ensures that a customer has access to
the Central Office network during a power outage. The CO/PBX tip and ring
are automatically transferred to the tip and ring of a preselected Single Line
Telephone. The Single Line Telephone can function in the system during
normal operation or can be only be used during a power failure. Each B64-
U(  ) KSU...

Page 466

July 2003 NEC Business Solutions Ltd
458 – P4Power Failure Transfer
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BSCard Interface Slot Assignment 7-1 

Page 467

Features and Specifications Manual P5 – 459
Doc. No. 8201 - Release 1.0
July 2003
Preset DiallingP-5
FEATURE 
DESCRIPTIONThe Preset Dialling feature enables a Multiline Terminal user to originate an
outgoing call by predialling digits on the keypad. After dialling the
number, the user can go off-hook, press the Speaker key, or press a line
key to make the call.
SYSTEM 
AVAILABILITYTerminal Type
Any Multiline Terminal.
Required Components
None.
OPERATING 
PROCEDURES
1. Dial the telephone number using the...

Page 468

July 2003 NEC Business Solutions Ltd
460 – P5Preset Dialling
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BTS4Class of Service (Station) Feature Selection 21-8-08 5-5
¶+AICaller ID Preset Dial Outgoing CO Selection 4-44
4When the system is at default this Memory Block must be programmed for the feature to be used. 

Page 469

Features and Specifications Manual P6 – 461
Doc. No. 8201 - Release 1.0
July 2003
Prime Line AssignmentP-6
FEATURE 
DESCRIPTIONPrime Line Assignment allows a station user to go off-hook and originate an
outside call from the trunk assigned as the Prime Line without pressing the
line key. This feature allows access to a trunk, Trunk group, or Route
Advance Block.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. Lift the handset or pressP. Prime Line...

Page 470

July 2003 NEC Business Solutions Ltd
462 – P6Prime Line Assignment
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSData Assignment
	Prime Line can be assigned to a Trunk or a Pooled Line (Trunk Group
or Route Advance Block) in system programming. There are two ways
to achieve this, with MB 4-23 or MB 4-05. Refer programming manual
for details.
	Prime Line is assigned per station.
Restrictions
	If Prime Line is busy or on Hold, a busy tone is received when going
off-hook. (Another line must be...
Start reading NEC Xen Ipk Features And Specifications Manual

Related Manuals for NEC Xen Ipk Features And Specifications Manual

All NEC manuals