NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual L4 – 401
Doc. No. 8201 - Release 1.0
July 2003
	If DND, Call Forward - All Call, or Station Outgoing Lockout is set
during Live Monitoring Mode, the Live Monitoring mode is cancelled. If
required, a station user must set up Live Monitoring mode after setting
Call Forward - All Call.
	Live Monitoring calls cannot be picked up by Call Pickup feature.
General
	Visual indications for Live Monitoring line key LED include the...

July 2003 NEC Business Solutions Ltd
402 – L4Live Monitoring
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual L5 – 403
Doc. No. 8201 - Release 1.0
July 2003
Loop Start TrunksL-5
FEATURE 
DESCRIPTIONLoop Start Trunks can be connected to the Xen IPK system via the COI ( )-
U(  ) ETU or COID( )-U(  ) ETU.
SYSTEM 
AVAILABILITYTerminal Type
Not applicable .
Required Components
COI( )-U(  ) ETU or COID( )-U(  ) ETU
OPERATING 
PROCEDURES
SERVICE 
CONDITIONS
General
	If the serving CO sends a disconnect signal when the outside party
abandons a call, the trunk is automatically...

July 2003 NEC Business Solutions Ltd
404 – L5Loop Start Trunks
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual M1 – 405
Doc. No. 8201 - Release 1.0
July 2003
Message WaitingM-1
FEATURE 
DESCRIPTIONA locally provided music source or an internal music source can be used to
supply music to parties on hold, to assure them that they are still connected
to the system.
System Software allows CO ports to provide multiple music sources to
different COs in the system.
SYSTEM 
AVAILABILITYTerminal Type
All terminals that are assigned on the Attendant Add-On Console, except
Single Line...

July 2003 NEC Business Solutions Ltd
406 – M1Message Waiting
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSGeneral
	A Message Waiting indication can be identified on the large LED on
the recipient Multiline Terminal. Message Waiting indications from the
Attendant Add-On Console flash green; indications from a Voice Mail
Unit flash red.
	To confirm a Message Waiting indication at an Attendant Add-On
Console, ensure that the green LED associated with the station is lit. A
Message Waiting...

Features and Specifications Manual M2 – 407
Doc. No. 8201 - Release 1.0
July 2003
Microphone ControlM-2
FEATURE 
DESCRIPTIONThe Microphone Control feature allows microphone control with ON/OFF
status indication on all Multiline Terminals. A Flexible Line key or One-Touch
key programmed for Microphone Control or an Access Code is used to
mute the microphone for privacy during incoming voice announcement calls
and during calls using the built-in speakerphone. 
D
term Series i Multiline Terminals have a...

July 2003 NEC Business Solutions Ltd
408 – M2Microphone Control
Doc. No. 8201 - Release 1.0
July 2003
When the MIC LED is off
1. Press
T.
2. Dial Access Code 
A.
3. The MIC LED goes on.
When the MIC LED is on
1. Press
T.
2. Dial Access Code 
A.
3. The MIC LED goes off.
SERVICE 
CONDITIONSGeneral
	D
term Series i Multiline Terminals have a built-in MIC key.
	The MIC key controls the built-in microphone during handsfree
mode and controls the handset mute feature during handset/headset
operation.
	The...

Xen IPK Features and Specifications Manual
Features and Specifications Manual M2 – 409
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BTMLine Key Selection for Telephone Mode4-12 

July 2003 NEC Business Solutions Ltd
410 – M2Microphone Control
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK