NEC Xen Ipk Features And Specifications Manual

Features and Specifications Manual R2 – 483
Doc. No. 8201 - Release 1.0
July 2003
Recall With Station 
IdentificationR-2
FEATURE 
DESCRIPTIONWhen the call is not answered in a specified time, it recalls with Station
Identification. During the recall, the Multiline Terminal display shows the
station number that is recalling and the station that did not answer. This
feature applies to transferred, held, or camped-on calls.
SYSTEM 
AVAILABILITYTerminal Type
Any Multiline Terminal with LCD.
Required...

July 2003 NEC Business Solutions Ltd
484 – R2Recall With Station Identification
Doc. No. 8201 - Release 1.0
July 2003
RELATED 
FEATURES LIST
GUIDE TO 
FEATURE 
PROGRAMMINGFeature 
NumberFeature Name
C-13 Call Park - System
I-1 I-Hold Indication
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BMHold Recall Time Selection (Non Exclusive Hold) 1-1-03
¶+BMStation Transfer/Camp-On Recall Time Selection  1-1-12
¶+BMSystem Call Park Recall...

Features and Specifications Manual R3 – 485
Doc. No. 8201 - Release 1.0
July 2003
Redial KeyR-3
FEATURE 
DESCRIPTIONUsers can press the Redial key and dial the Speed Dial buffer number to
access System and Station Speed Dial. Users can also press the Redial key
and # to redial the last outside number dialled.
SYSTEM 
AVAILABILITYTerminal type
All Multiline Terminals.
Required Components
None.
OPERATING 
PROCEDURES
Last Number Redial
Key Function
1. Press an idle CO/PBX/Tie line key.
2. Press 
Q.
3. Dial...

July 2003 NEC Business Solutions Ltd
486 – R3Redial Key
Doc. No. 8201 - Release 1.0
July 2003
Multifunction (Dial Access)
1. Press 
Q.
2. Dial the Speed Dial buffer number (
00~II).
SERVICE 
CONDITIONSGeneral
	The last outside line number (24 digits maximum) that is dialled is
automatically redialled.
	The Redial key feature can be assigned to a Feature Access or
One-Touch key. 
RELATED 
FEATURES LIST
GUIDE TO 
FEATURE 
PROGRAMMINGFeature 
NumberFeature Name
L-2 Last Number Redial
S-10 Speed Dial –...

Features and Specifications Manual R4 – 487
Doc. No. 8201 - Release 1.0
July 2003
Remote ProgrammingR-4
FEATURE 
DESCRIPTIONRemote Programming provides a method to modify and save all system
parameters from a remote location using a modem. This is a variation of the
Maintenance Access Terminal (MAT) PC Programming, and additional
software other than PC Programming is not required.
SYSTEM 
AVAILABILITYTerminal type
Not Applicable.
Required Components
PC with MAT PC Programming and modem installed at the...

July 2003 NEC Business Solutions Ltd
488 – R4Remote Programming
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BSCard Interface Slot Assignment 7-1
¶+CSS4Modem Number for Remote Programming 
Assignment1-8-38
¶+BCTDIT Assignment 3-42
¶+BCTANA Assignment 3-43
4When the system is at default this Memory Block must be programmed for the feature to be used. 

Features and Specifications Manual R5 – 489
Doc. No. 8201 - Release 1.0
July 2003
Resident System ProgramR-5
FEATURE 
DESCRIPTIONWhen power is supplied to the system, the hardware configuration is
scanned and Resident System Program default values are assigned. This
enables immediate operation, even before the system is programmed to
accommodate the individual site requirements.
SYSTEM 
AVAILABILITYTerminal Type
Not applicable.
Required Components
None.
OPERATING 
PROCEDURES
SERVICE 
CONDITIONS
General...

July 2003 NEC Business Solutions Ltd
490 – R5Resident System Program
Doc. No. 8201 - Release 1.0
July 2003
	Default Attendant Add-On Console key assignments are:  
	A First Initialisation of the system returns all programming values to
default. This can be performed by disconnecting the battery on the
CPUI(  )-U(  ) ETU and turning off system power.
DSS KeysAssignment
01~48 Stations 100~147 (if installed)
49 Night Mode Change
50 Internal Paging Zone A
51 Internal Paging Zone B
52 Internal Paging Zone C...

Features and Specifications Manual R6 – 491
Doc. No. 8201 - Release 1.0
July 2003
Restriction (Outgoing)R-6
FEATURE 
DESCRIPTIONThe Restriction (Outgoing) feature denies station users the ability to
originate outside calls per station/per trunk. At stations where Outgoing
Restriction is assigned, users can continue to answer incoming calls, place
and receive internal calls, and pick up held lines on a specified trunk. The
number of digits dialled on outgoing calls may also be restricted per station....

July 2003 NEC Business Solutions Ltd
492 – R6Restriction (Outgoing)
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-Line 
Key
¶+BTT4Trunk Outgoing Restriction4-19
4When the system is at default this Memory Block must be programmed for the feature to be used.