NEC Xen Ipk Features And Specifications Manual

Features and Specifications Manual D11 – 271
Doc. No. 8201 - Release 1.0
July 2003
Direct Paging AccessD-11
FEATURE 
DESCRIPTIONThe Attendant Add-On Console Direct Station Selection/Busy Lamp Field
(DSS/BLF) keys allow direct access to each of the Internal, External, and All
Call Paging. The programmable Feature Access and One-Touch keys on
the Multiline Terminals can also be used for Direct Paging Access.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals and Attendant Add-On Consoles .
Required...

July 2003 NEC Business Solutions Ltd
272 – D11Direct Paging Access
Doc. No. 8201 - Release 1.0
July 2003
Restrictions
	All Internal/External Page Access cannot be programmed to a key on
the Attendant Add-On Console.
General 
	If a Direct Paging Access key for All Internal Zone or Internal Zone
Page on the Attendant Add-On Console is pressed, a paging
announcement is made over the speakers of all idle Multiline Terminals
programmed in a zone. 
	Paging access through external speakers is available if a...

Features and Specifications Manual D12 – 273
Doc. No. 8201 - Release 1.0
July 2003
Direct Station SelectionD-12
FEATURE 
DESCRIPTIONThe Direct Station Selection (DSS) feature allows all Multiline Terminal
users to make station calls by pressing only one key.
SYSTEM 
AVAILABILITYTerminal Type
All Multiline Terminals and Attendant Add-On Consoles.
Required Components
None.
OPERATING 
PROCEDURES
1. Press the programmed Feature Access key. Hear ringback tone or
make voice announcement.
2. When the called...

July 2003 NEC Business Solutions Ltd
274 – D12Direct Station Selection
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSGeneral
	When station numbers are assigned to Feature Access or One-Touch
keys on a Multiline Terminal, the user can press the DSS key to call the
station.
	When a station is called by pressing a DSS key and that station is
busy, a call waiting tone is sent to the calling station. Any other station
that calls the original busy station receives a busy tone while the first
calling...

Features and Specifications Manual D13 – 275
Doc. No. 8201 - Release 1.0
July 2003
Distinctive RingingD-13
FEATURE 
DESCRIPTIONThe Distinctive Ringing feature distinguishes between internal and incoming
outside calls. This feature provides distinct ring audible signals
and patterns.
Distinctive Ring can be assigned on a per trunk or per telephone basis.
SYSTEM 
AVAILABILITYTerminal Type
All terminals, except Single Line Telephones connected to an AP(R)-
R( ) Unit.
Required Components
None.
OPERATING...

July 2003 NEC Business Solutions Ltd
276 – D13Distinctive Ringing
Doc. No. 8201 - Release 1.0
July 2003
General
	Incoming outside calls and internal calls provide flexible ringing tones
and patterns.
	Distinctive ringing patterns are as follows:
1. Internal ring tone provides a distinctive ringing pattern of 1 second
ON/2 seconds OFF (system default).
2. Incoming CO/PBX outside calls are assigned synchronous ring.
The ringing pattern sent from the exchange connected to
the CO PBX/Centrex lines is...

Xen IPK Features and Specifications Manual
Features and Specifications Manual D13 – 277
Doc. No. 8201 - Release 1.0
July 2003
 
GUIDE TO 
FEATURE 
PROGRAMMING
Incoming Trunk Call 
Priority?
M. B.  4- 57
Ca ll? D IT, AA, or DID
M.B. 4-55?
M.B. 3-67?
CO TEL
Yes
No
Ca ll? D IT, AA, or DID
– (N on e)
M. B.  3- 67 ? A~H
Ye s
No
A~H – ( Non e)
To ne  F oll ows
M.B.3-07
– (None)
Ton e Fo llo ws
M.B.3-07
To n e  F o l l o w s
M. B . 4-9 1Individual
for R inging  Port
CO/PBX Trunk?
M. B.  1 -1- 59
Synchronous?...

July 2003 NEC Business Solutions Ltd
278 – D13Distinctive Ringing
Doc. No. 8201 - Release 1.0
July 2003
¶+BTS4Distinctive Ringing by Telephone or CO 
Selection1-1-28
¶+BCTCO/PBX Ringing Variation Selection 3-07
¶+BTMTelephone Ringing Variation Selection 4-91
¶+BCSCO Line Ringing Pattern Selection 1-1-51
¶+BCSPBX Line Ringing Pattern Selection 1-1-52
¶+ALNTie Line Delay Ring Pattern Selection 1-1-53
¶+BMCO/PBX Incoming Ringing Alarm Time Selection 1-1-06
¶+ALMTie Line Delay Ringing Time Selection 1-1-07...

Features and Specifications Manual D14 – 279
Doc. No. 8201 - Release 1.0
July 2003
Do Not Disturb (DND)D-14
FEATURE 
DESCRIPTIONThe Do Not Disturb (DND) feature temporarily eliminates all audible signals
for incoming calls to the station. This temporarily isolates the station from
others in the system.
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES
1. PressTin idle mode.
2. Dial Access Code
F0.
3. Press
T.
- OR -
4. Press the DND On/Off key.
1. Lift the...

July 2003 NEC Business Solutions Ltd
280 – D14Do Not Disturb (DND)
Doc. No. 8201 - Release 1.0
July 2003
1. Lift the handset or press P.
2. Dial DND cancel;
DB(set at default).
3. Go on-hook or press
P.
1. Press
T.
2. Dial Access Code
FH.
3. Press
T.
SERVICE 
CONDITIONSData Assignment
	At default, the system-wide cancel DND from Attendant Positions is
not allowed.
	DND is allowed or denied in Class of Service.
Restrictions
	Automatic Callback cannot be set to a station that is in DND mode.
	If DND and...