NEC Xen Ipk Features And Specifications Manual

Xen IPK Features and Specifications Manual
Features and Specifications Manual D8 – 261
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-
Line Key
¶+BSCard Interface Slot Assignment 7-1
¶+BCT4Trunk-to-Trunk Group Assignment3-03
¶+BCT4Trunk Type Selection3-91
¶+ALTTie Line Type Assignment 3-14
¶+ALNTie Line First Ring Pattern Selection 1-1-34
¶+ALNTie Line Delay Ring Pattern...

July 2003 NEC Business Solutions Ltd
262 – D8Direct Inward Dialling (DID)
Doc. No. 8201 - Release 1.0
July 2003
¶+ALNDID Digit Conversion Table 1-1-22
¶+BTSClass of Service (Station) Feature 
Selection 21-8-084-3, 4-4
5-7
¶+BTTStation to Class of Service Feature Assignment 4-17
¶+BNDID Limit to Tenant Assignment 2-09
¶+BNTrunk to Tenant Assignment 2-01
¶+BNLine Key Selection 2-05
¶+BNLine Key Selection for Tenant Mode 2-06
¶+BTMLine Key Selection for Telephone Mode 4-12
¶+BTTTelephone to Tenant...

Features and Specifications Manual D9 – 263
Doc. No. 8201 - Release 1.0
July 2003
Direct Inward System 
Access (DISA)
D-9
FEATURE 
DESCRIPTIONDirect Inward System Access allows an outside caller to access the system
from an outside line without Attendant or station assistance. The outside
user may originate calls over any or all of the system facilities such as a Tie
line network or CO/PBX trunk after successfully entering a password.
SYSTEM 
AVAILABILITYTerminal Type
Not applicable.
Required Components...

July 2003 NEC Business Solutions Ltd
264 – D9Direct Inward Dialling (DID)
Doc. No. 8201 - Release 1.0
July 2003
1. Go off-hook.
2. Dial the DISA password set Access Code _______ (default not
assigned).
3. Enter the ID code (station number is default).
4. Enter the DISA password
(default: 
0000000000).
5. Enter the new DISA password (maximum: 10 digits).
6. Go on-hook.
1. Go off-hook.
2. Dial the DISA password reset Access Code _______ (default not
assigned).
3. Enter the ID code (station number is...

Xen IPK Features and Specifications Manual
Features and Specifications Manual D9 – 265
Doc. No. 8201 - Release 1.0
July 2003
SERVICE 
CONDITIONSData Assignment
	A DISA Access Code is entered using System Programming.
General
	DTMF signalling is required from the outside caller.
	When the DISA feature is activated, incoming outside callers hear a
special tone when DISA trunks are called. These trunks can still be
used for outgoing calls.
	A maximum 64 trunks for DISA can be installed in the Xen IPK...

July 2003 NEC Business Solutions Ltd
266 – D9Direct Inward Dialling (DID)
Doc. No. 8201 - Release 1.0
July 2003
GUIDE TO 
FEATURE 
PROGRAMMING
Order
and
Shortcut
System Data NameMemory 
BlockFunction
1-8-07
Attendant
Page-Line 
Key1-8-08
Station
Page-
Line Key
¶+BAAccess Codes (1-, 2-, 3-Digit) Assignment 1-1-46/47/48 251~ 253,
¶+AU4Automated Attendant Message Day/Night Mode 
Selection1-4-11
¶+BTI4SLT or Automated Attendant/DISA to PBR 
Selection1-8-01
¶+BCT4Trunk Incoming Answer Mode Selection3-05...

Xen IPK Features and Specifications Manual
Features and Specifications Manual D9 – 267
Doc. No. 8201 - Release 1.0
July 2003
¶+AUAutomated Attendant No Answer Disconnect Time 
Selection1-4-03
¶+BTTCO/PBX Ring Assignment (Day Mode) 4-01
¶+BTTCO/PBX Ring Assignment (Night Mode) 4-02
¶+BITone Assignment1-8-15
(Tone Table)
¶+ATTandem Transfer SMDR Print Extension 
Assignment1-4-04
4When the system is at default this Memory Block must be programmed for the feature to be used.
Order
and
Shortcut
System Data...

July 2003 NEC Business Solutions Ltd
268 – D9Direct Inward Dialling (DID)
Doc. No. 8201 - Release 1.0
July 2003
THIS PAGE INTENTIONALLY LEFT BLANK 

Features and Specifications Manual D10 – 269
Doc. No. 8201 - Release 1.0
July 2003
Direct Inward Termination 
(DIT)
D-10
FEATURE 
DESCRIPTIONDirect Inward Termination (DIT) allows CO/PBX lines to be programmed to
ring directly at stations (bypassing the Attendant). A separate Assigned
Night Answer (ANA) ringing assignment is available. A System or Tenant
group can be set to the Night Mode independently. 
SYSTEM 
AVAILABILITYTerminal Type
All terminals.
Required Components
None.
OPERATING 
PROCEDURES...

July 2003 NEC Business Solutions Ltd
270 – D10Direct Inward Termination (DIT)
Doc. No. 8201 - Release 1.0
July 2003
	When a busy station programmed for DIT receives an incoming DIT
call, the system provides Camp-On tone for the busy station. The
calling party receives ringback tone until the call is answered.
	When a busy station receives an incoming DIT Camp-On tone, the
existing call can be terminated [held (including Call Park),
automatically held, or transferred] to enable the station user to answer...