Home > NEC > Communications System > NEC Neax2000 Ivs Small Platform System Manual

NEC Neax2000 Ivs Small Platform System Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual NEC Neax2000 Ivs Small Platform System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 182
    Add page 41 to Favourites
    image text
    Enable zoom 
    							ND -4 6551 ( E)  CHAPTER 3
NAP-200-0 02
3 82 mm
25 0  m m
430 mm
PBX B OTT OM  P O SIT IO N
BO TTO M P OSITI ON
    Add page 42 to Favourites
    image text
    Enable zoom 
    							CHAPTER 3 ND-46551 (E)
Pag e 3 0
Revision 2.0
NAP-200-002
Sheet 3/3
Marking and Drilling
3. DRILLING 
• Drilling and installing anchor bolts
Figure 002-3  Instruction for Anchor Bolt
 
(1) DRILL A HOLE IN THE CONCRETE WITH A 
DRILL SUITABLE FOR A PLUG BOLT A LITTLE 
DEEPER THAN THE PLUG BOLT LENGTH.
(2) INSERT THE ANCHOR BOLT INTO THE HOLE.
(3) PUSH ANCHOR BOLT UNTIL THE BOLT 
STAYS PERMANENTLY IN PLACE.
(4) TURN BOLT COUNTERCLOCKWISE AND 
REMOVE.(1) (2) (3) (4)
    Add page 43 to Favourites
    image text
    Enable zoom 
    							ND-46551 (E) CHAPTER 3
Page 31
Revision 2.0
NAP-200-003
Sheet 1/21
Installation of Main Equipment
Install the main equipment according to the desired procedure for either Floor Standing, Wall-Mounting, 19-Inch
Rack-Mounting or Desk Top installation.
1. FLOOR STANDING INSTALLATION
(1) Attaching the BASE to the floor.
• Position the BASE over the holes drilled as shown in the figure below.
• Secure the BASE to the floor using anchor bolts.
Figure 003-1  Securing of the BASE
BASE
FRONT
INSTALLATION HOLEANCHOR BOLT
    Add page 44 to Favourites
    image text
    Enable zoom 
    							CHAPTER 3 ND-46551 (E)
Pag e 3 2
Revision 2.0
NAP-200-003
Sheet 2/21
Installation of Main Equipment
(2) Mount the PIM on the BASE, and connect them together using 3 bolts (provided).
Figure 003-2  Mounting of the PIM
PIM
BASE
FRONT
    Add page 45 to Favourites
    image text
    Enable zoom 
    							ND-46551 (E) CHAPTER 3
Page 33
Revision 2.0
NAP-200-003
Sheet 3/21
Installation of Main Equipment
(3) Position the TOP COVER on the PIM, and connect them together with 4 screws (provided).
Figure 003-3  Mounting of the TOP COVER
TOP COVER
PIM
FRONT
    Add page 46 to Favourites
    image text
    Enable zoom 
    							CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 03
    Add page 47 to Favourites
    image text
    Enable zoom 
    							ND -4 6551 ( E)  CHAPTER 3
NAP-200-0 03
SCR EW- A (4  p er PI M)
M4 M ACHINE SCRE W-B  (4 p er  P IM )
(W ALL)
38 2 m m(1 5.0  in ch )
ANCHO R (4  p er PI M)
RA CK PA RTS
(9 .8 i nch )
    Add page 48 to Favourites
    image text
    Enable zoom 
    							CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 03
(PI M)
(RE AR COVER)
    Add page 49 to Favourites
    image text
    Enable zoom 
    							ND-46551 (E) CHAPTER 3
Page 37
Revision 2.0
NAP-200-003
Sheet 7/21
Installation of Main Equipment
(4) After hanging PIM onto the RACK PARTS, tighten each M4 machine screw using a phillips screw driver.
Figure 003-6  Screwing the PIM to the RACK PARTS
M4 MACHINE SCREW-B (X4)
PIMRACK PARTS
    Add page 50 to Favourites
    image text
    Enable zoom 
    							CHAPTER 3 ND-46551 (E)
Pag e 3 8
Revision 2.0
NAP-200-003
Sheet 8/21
Installation of Main Equipment
(5) Connect the TOP COVER, BOTTOM COVER and AC CORD-A-U to the PIM. The AC CORD-A-U is
pre-installed with the BOTTOM COVER.
Figure 003-7  Connecting the Covers and AC CORD to the PIM
TOP COVER
TO PZ-PW86 PIM
AC CORD-A-U
BOTTOM COVER
LOCAL CABLE DUCT
    All NEC manuals Comments (0)

    Related Manuals for NEC Neax2000 Ivs Small Platform System Manual