NEC Neax2000 Ivs Small Platform System Manual
Have a look at the manual NEC Neax2000 Ivs Small Platform System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-46551 (E) CHAPTER 3 Page 149 Revision 2.0 NAP-200-010 Sheet 7/7 System Initialization and System Data Entr y DESCRIPTION DATA Assign the type of signaling (DTMF) for Outgoing and Bothway Trunk Routes..YY = 01 (1) Trunk Route No. (00 - 63) (2) 7 Specify the DTMF Sender characteristics to match the distant office..YY = 24 (DTMF Inter Digital Pause) (1) Trunk Route No. (00 - 63) .YY = 26 (DTMF Sender Signal Width) (1) Trunk Route No. (00 - 63) (2) 0/1 : 64ms/128ms .YY = 46 (DTMF Sender Release Timing) (1) Trunk Route No. (00 - 63) Assign whether “*” or “#” from a DTMF Telephone is used as Switch Hook Flash while hearing Busy Tone.(1) 050 (* is used as Switch Hook Flash) (2) 0: Available (1) 052 (# is used as Switch Hook Flash) (2) 0: Available CM35 CM08 END A 0: 32ms 1: 64ms 2: 80ms 3: 96ms 4 : 160ms 5 : 192ms 6 : 240ms 7 : 128ms 0: 2sec. 1: 4sec. 2: 6sec. 3: 8sec. 4 : 12sec. 5 : 14sec. 6 : 16sec. 7 : 10sec. (2) (2)
CHAPTER 3 ND-46551 (E) Pag e 1 50 Revision 2.0 NAP-200-011 Sheet 1/1 Operation Test 1. OPERATION TEST Confirm the entered system data and hardware, including cable connection, by completing the following operational tests. • Basic Connection Test at MDF - Station Line Test (Operator Call from all stations) - Central Office Trunk Test (Incoming, Outgoing) - Tie Line Trunk Test (Incoming, Outgoing) • Service Feature Test - Call Transfer - Step Call - Executive Right of Way - Call Hold - Call Back - Call Forwarding-All Calls/No Answer/Busy Line - Call Pickup - Station Hunting-Pilot/Circular - Speed Calling-System/Station - Paging Access - Announcement Service -etc.
ND-46551 (E) CHAPTER 3 Page 151 Revision 2.0 NAP-200-012 Sheet 1/1 Cleaning and Visual Check 1. CLEANING Clean the following places: • Inside of the main equipment, especially the bottom of the base. • On the Top Cover. • Around the Main Equipment and the MDF. • Keyboard on the Attendant Console. 2. VISUAL CHECK (1) Check to see if all circuit cards are in their positions correctly. (2) Check that the cable connections in the PIM are correctly and completely connected, and the routing of the cables has been done smoothly and neatly. (3) Check to see if the MAT is removed.
CHAPTER 3 ND-46551 (E) Pag e 1 52 Revision 2.0 NAP-200-013 Sheet 1/1 Mounting of the Front Cover 1. MOUNTING OF THE FRONT COVER Mount the Front Cover onto PIM and attach them with screw provided. Figure 013-1 Mounting of the Front Cover PIM FRONT FRONT COVER
ND -4 6551 ( E) CHAPTER 4 CHAPTER 4 OFFICE D ATA P ROGRAM MING
CHAPTER 4 ND-46551 (E) Pag e 1 54 Revision 2.0 1.2.2 Station Data In this table, the following data are required. • Station Number: Station numbers (up to four digits), specified in the Numbering Plan Table, are assigned. For the Multiline Terminal station, specify the Primary Extension Number. • Type of Telephone The type of station telephone set is specified as shown below. TYPE OF TEL DESCRIPTION DP ................................... Dial Pulse Telephone set PB ................................... DTMF Telephone set Multiline Terminal.......... Multiline Terminal set • SERVICE CLASS-A/B/C Specify the service class (1-15) programmed in the Service Restriction Data Table. • RESTRICTION CLASS-DAY/NIGHT Specify the Trunk Restriction Class as shown below. 1: Unrestricted 2: Non-Restricted-1 3: Non-Restricted-2 4: Semi-Restricted 1 5: Semi-Restricted 2 6: Restricted 1 7: Restricted 2 8: Fully-Restricted • DIT TRUNK NUMBER In the case of the DIT (Direct-In Termination) station, specify the trunk number connected. 1.2.3 Trunk Data In this table, the following data are required: • ACCESS NUMBER Specify the access code for the trunks. • DESTINATION Specify the distant office such as Central Office (Public Exchange), Tie Line, etc.
ND-46551 (E) CHAPTER 4 Page 155 Revision 2.0 • NUMBER OF LINE Specify the number of trunks to be provided with each route (IC-Incoming, OG-Outgoing, BW-Bothway). • DP/PB Specify the type of address signal from/to distant office, as shown below. TYPE OF TEL DESCRIPTION DP ................................... Dial Pulse PB ................................... DTMF Signal • KIND OF SIGNAL Specify the kind of signaling system such as Ring Down, Loop, E & M etc. at the line. 1.2.4 Station Hunting Group Data This data table requires the following data: • KIND OF STATION HUNTING Specify the kind of the Station Hunting System (Pilot/Circular/Switch Back). In the case of the Pilot Sys- tem, specify the Pilot Station Number. • SECRETARY STATION Specify the Secretary Station Number, if provided. • STATION NUMBER Specify the station numbers to be assigned to the station hunting group with the following conditions. (1) Up to 60 stations can be assigned per Station Hunting Group. (2) There is no limitation to the number of Station Hunting Groups. The same one station cannot be assigned to multiple Hunting Groups. 1.2.5 Call Pickup Group Data The station number to be assigned to the Call Pickup Group with the following conditions. (1) Up to 60 station can be assigned per Call Pickup Group. (2) There is no limitation to the number of Call Pickup Groups. (3) The same one station cannot be assigned to multiple Call Pickup Groups.
CHAPTER 4 ND -4 6551 ( E) 1.2 .6 Speed C allin g-S yste m D ata L EV EL 3 L EV EL 2 Sta ti on No. LEV EL 7/T ru nk No. P ri m ary E xte n si on Nu mber L EV EL 3 L EV EL 2 Not t o b e L EV EL 7 Sta ti on No.Pri m ary E xte n si on Nu mber
ND-46551 (E) CHAPTER 4 Page 157 Revision 2.0 PN-AUC PN-2DLC• The station number must be assigned to the 1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT slot. • For the PN-2DLC, specify the Primary Extension Numbers of Multiline Terminal as shown below. PN-4COT PN-4DIT• The trunk number must be assigned to the 1st LEN (LEVEL 0) through 4th LEN (LEVEL 3) of each LT s l o t . PN-AUC PN-2ODT• The trunk number must be assigned to the 1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT slot. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 – 0003 – 0002 201 0001 200 0000 Station No. assigned FXXX Primary Extension Number LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 D003 0003 D002 0002 D001 0001 D000 0000 assigned Trunk No. (D000-D255) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 D003 0003 D002 0002 D001 0001 D000 0000 Trunk No. assigned(D000-D255)
CHAPTER 4 ND-46551 (E) Pag e 1 58 Revision 2.0 PN-2DAT • The card number must be assigned to the 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. PN-8RST • The card number must be assigned to the 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. Note :When using the internal DTMF Receiver on the MP card, assign the Card No. E200 to the LEN No. 0124. PN-DK00 • The card number must be assigned to the 1st LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT slot. • The card numbers of External Equipment Interface are E800-E807. • The card numbers of External Key Interface are E900-E915. Table 4-2 Port Assignment Method (Continued) CARD TO BE ASSIGNEDPORT ASSIGNMENT TABLE REMARKS LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 – 0003 EB001 0002 – 0001 EB000 0000 Card No. assigned(EB000-EB031) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 – 0003 E201 0002 – 0001 E200 0000 Card No. assigned(E200-E203) LEVEL 3 LEVEL 2 LEVEL 1 LEVEL 0 Not to be LEVEL 7 LEVEL 6 LEVEL 5 LEVEL 4 LT 0 0 – 0007 – 0006 – 0005 – 0004 – 0003 E801 0002 – 0001 E800 0000 Card No. assigned(E800-E807) (E900-E915)