NEC Neax2000 Ivs Small Platform System Manual
Have a look at the manual NEC Neax2000 Ivs Small Platform System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-46551 (E) CHAPTER 3 Page 119 Revision 2.0 NAP-200-007 Sheet 4/11 Installation of SN716 DESKCON (c) MDF Cross Connection via PN-PW00 Power Option (see Figure 007-4) Figure 007-4 MDF Cross Connection via PN-PW00 Power Option 26 Bx 1 Ax LTC0 (J) 1Ax26Bx (P) LEN0000 1 Grd 26 -48V 2 Grd 27 -48V (P) MDF LEN0000 Ax Bx Ax Bx PN-8DLCPIM0 1 26 1 2 3 4 5 6 MODULAR TERMINALPW00 Grd -48V Grd -48V SN716 DESKCON
CHAPTER 3 ND-46551 (E) Pag e 1 20 Revision 2.0 NAP-200-007 Sheet 5/11 Installation of SN716 DESKCON (1) Handset Installation Screw the handset support onto the bottom of the console. Figure 007-5 Mounting of Handset Support to SN716 DESKCON
ND-46551 (E) CHAPTER 3 Page 121 Revision 2.0 NAP-200-007 Sheet 6/11 Installation of SN716 DESKCON (2) Headset Installation Plug the headset into the modular jack (H/S 0 or H/S 1) located at the bottom of the console. Figure 007-6 Headset Installation for SN716 DESKCON HAND H/S 0 H/S 1
CHAPTER 3 ND-46551 (E) Pag e 1 22 Revision 2.0 NAP-200-007 Sheet 7/11 Installation of SN716 DESKCON (3) Line Cord Connection Plug the line cord into the modular jack (LINE) located at the bottom of the console. For the MDF cross connection for the SN716 DESKCON, refer to Figure 007-7. Figure 007-7 Cable Connection to SN716 DESKCON PBX DLC 1P MDF MODULAR TERMINAL SN716 DESKCON3P 3P PW00 2P LINE CORD PAGE REC LINE
ND-46551 (E) CHAPTER 3 Page 123 Revision 2.0 NAP-200-007 Sheet 8/11 Installation of SN716 DESKCON (4) AC-DC ADAPTER Connection When using an AC-DC ADAPTER for power supply, plug the AC-DC ADAPTER into the “12V~24VDC” terminal located at the rear of the console. Figure 007-8 AC-DC ADAPTER Connection to SN716 DESKCON AC-DC ADAPTER RS-232 12V~24VDC
CHAPTER 3 ND-46551 (E) Pag e 1 24 Revision 2.0 NAP-200-007 Sheet 9/11 Installation of SN716 DESKCON (5) Using PW00 Card When using the PW00 card for power supply, provide the PW00 card according to the following procedure. (a) Mount the PW00 card into the LT01-LT10 slot or AP5 slot. Figure 007-9 Mounting PW00 Card into PIM BUILT-IN BATTERY Note: The PW00 card occupies the adjoining left side (smaller number) slot because of its two-story structure. PIM P W R LT00LT01LT02LT03LT04LT05LT06/AP0LT07/AP1LT08/AP2LT09/AP3LT10/AP4 AP5MP PW00
ND-46551 (E) CHAPTER 3 Page 125 Revision 2.0 NAP-200-007 Sheet 10/11 Installation of SN716 DESKCON (b) Connect the PW00 card and SN716 DESKCON by installation cable as shown in Figure 007-10 and Figure 007-11. Figure 007-10 PW00 Card Connection to SN716 DESKCON PW86 PW00 CONN Connector PWR0C PIMPWR1 TO DESKCON
CHAPTER 3 ND-46551 (E) Pag e 1 26 Revision 2.0 NAP-200-007 Sheet 11/11 Installation of SN716 DESKCON (6) 6.MDF Cross Connection (a) When using PN-8DLC Figure 007-11 MDF Cross Connection for SN716 DESKCON 33T7338 R7832 T6327 R6727 T12726 T026 2 1 MDF R01 R12 LEN0000 (No. 0) PIM0 P PN-8DLC LT00LTC0 J LEN0001 (No. 1) LEN0006 (No. 6) LEN0007 (No. 7) • •• •• •• • 1R026T0 2R127T1 7R632T6 8R733T7 (P) 26 T0 1 R0 27 T1 2 R1 32 T6 7 R6 33 T7 8 R7LEN0000 LEN0001 LEN0006 LEN0007 LTC0 (J) • •• •• •• •• •• •• •• • • • Note 1:When power is supplied by the AC-DC ADAPTER, this connection is not required. Note 2:The same connection is required when using 4DLC/2DLC. 08 07 06 05 04 03 02 01 PN-PW00 –48V –48VE E–48V –48VE E MODULAR TERMINAL 1 2 3 4 5 6Note 1 Note 1 TO SN716 DESKCON
ND-46551 (E) CHAPTER 3 Page 127 Revision 2.0 NAP-200-008 Sheet 1/13 Switch Setting of Circuit Card 1. CIRCUIT CARDS SWITCH SETTING Table 008-1 shows the control circuit cards and Table 008-2 shows the line/trunk circuit cards to be explained in this NAP. As for the other circuit cards, refer to the Circuit Card Manual. *MB=Make BusyTable 008-1 Control Circuit Cards NAME (FUNCTIONAL NAME)EXISTENCE OF LAMPS X: PROVIDED —: NOT PROVIDEDEXISTENCE OF SWITCHES X: PROVIDED —: NOT PROVIDEDEXTRACTION/INSER- TION WITH POWER ON X: ALLOWED D: ALLOWED AFTER MB* —: NOT ALLOWEDREFERENCE PA G E PN-CP03 (MP) X X —128 PZ-PW86(C) (PWR)XX —131 PZ-PW86(D) (PWR)XX —134 PN-PW00 (EXTPWR)XX D136 Table 008-2 Line/Trunk Circuit Cards NAME (FUNCTIONAL NAME)EXISTENCE OF LAMPS X: PROVIDED —: NOT PROVIDEDEXISTENCE OF SWITCHES X: PROVIDED —: NOT PROVIDEDEXTRACTION/INSER- TION WITH POWER ON X: ALLOWED —: NOT ALLOWEDREFERENCE PAG E PN-8DLCJ/ 8DLCP (DLC)X— X138 PN-8LCS (LC) X — X139
CHAPTER 3 ND-46551 (E) Pag e 1 28 Revision 2.0 NAP-200-008 Sheet 2/13 Switch Setting of Circuit Card 2. PN-CP03 (MP) (1) Locations of Lamps, Switches, and Connectors Figure 008-1 PN-CP03 (MP) Card (2) Lamp Indications Table 008-3 PN-CP03 (MP) Card Lamp Indications LAMP NAME COLOR FUNCTION RUN Green Flashes at 120 IPM while the circuit card is operating normally. CLKIN Green Lights while receiving clock signals to the PLO oscillator. SW3 RUN SW1 SW2 CLK JP0 RS1 JACK VR RS0 JP1