NEC Neax2000 Ivs Small Platform System Manual

							ND-46551 (E) CHAPTER 3
Page 139
Revision 2.0
NAP-200-008
Sheet 13/13
Switch Setting of Circuit Card
7. PN-8LCS (LC)
(1) Locations of Lamps, Switches and Connectors
Figure 008-6  PN-8LCS (LC) Card
(2) Lamp Indications
(3) Switch Settings
This card has no switches.
Table 008-12  PN-8LCS (LC) Card Lamp Indications
LAMP NAME COLOR FUNCTION
BL0 - 7 Red• Remains lit when the corresponding circuit is in use.
• Flashes at 60 IPM when the corresponding circuit is in the make-busy state or the 
system data for this card is not assigned.
BL7
BL4BL6
BL5
BL3
BL2
BL0 BL1 
						

							CHAPTER 3 ND-46551 (E)
Pag e 1 40
Revision 2.0
NAP-200-009
Sheet 1/3
Mounting of Circuit Cards
1. MOUNTING PROCEDURE
(1) For testing, turn on “SW1” switch on the PZ-PW86 Card.  Make sure that “ON” lamp (Green) is lit.
(2) Turn off “SW1” switch.
Figure 009-1  PZ-PW86(C) Card Lamp Indication
PZ-PW86
ON
OFFSW1 SWITCH
ON LAMP (GREEN)
MN
MJ
ON 
						

							ND -4 6551 ( E)  CHAPTER 3
NAP-200-0 09
CARD  FRONT  SIDE
WR IST  STRAP
TO  FRA ME GROUND  CONNECTION
CARD CONT ACT S IDE 
						

							CHAPTER 3  ND -4 6551 ( E)
NAP-2 00-0 09
A
B
F ig . A 
						

							ND-46551 (E) CHAPTER 3
Page 143
Revision 2.0
NAP-200-010
Sheet 1/7
System Initialization and 
System Data Entr y
1. SYSTEM INITIALIZATION
• There are two methods for System Initialization.  The first method is to Clear All Data, except LEN0000
as a CAT terminal, and then program the System Data.  The second method is to use the Resident System
Program, which causes the system to configure itself automatically to the default settings, wherever the
line/trunk cards are installed.  Refer to the System Data Sheet, for the default settings. 
• Turn on the “SW1” switch on the PZ-PW86 card.
- The “ON” lamp must be lit on the PZ-PW86 card.
1.1 All Clear, Except LEN0000 CAT
STEP 1:
On the MP Card, set SW3 to “B” and press SW1.
STEP 2:
When the “MN” lamp on the system is lit, set SW3 to the “0” position and press SW1.
- The operating mode has been changed to the ON LINE mode.
1.2 Resident System Program
STEP 1:
Mount the Line/Trunk cards into PIM.
STEP 2:
On the MP Card, set SW3 to “C” and press SW1.
- After 30 to 40 seconds, the “MN” lamp turns on.
- The system has loaded the Resident System Program.
Note:If the “MJ” lamp is lit, repeat Step 2.
STEP 3:Set SW3 to the “0” position and press SW1.
- The operating mode has been changed to the ON LINE mode.
Note:Refer to the System Data Sheet for additional information on the Resident System Program and the initialization of
the system without a MAT (enabling CAT mode). 
						

							CHAPTER 3 ND-46551 (E)
Pag e 1 44
Revision 2.0
NAP-200-010
Sheet 2/7
System Initialization and 
System Data Entr y
2. SYSTEM DATA ENTRY
• There are two methods for data entry, both of which employ a Customer Administration Terminal (CAT)
or a Maintenance Administration Terminal (MAT).
2.1 CAT
Any Multiline Terminal can be assigned as a CAT terminal through programming.  The Multiline Terminal can still
be used as a regular telephone when it is not in CAT mode.  If the system is initialized by “C” (Resident System
Program), every Multiline Terminal will be able to go into CAT mode.  If the system is initialized by “B” (All Clear),
only LEN0000 is assigned as a CAT port (the DLC card must be installed in slot LT00).
To use a Multiline Terminal as a CAT, follow the procedures shown below.
To set CAT mode:
(1) Press
(2) Press
- CNF lamp flashes
(3) Press
- CNF lamp is off
(4) Press
(5) Press
- CNF lamp flashes
(6) Press
- CNF, SPKR, ANS lamps are lit
- “CAT MODE” is displayed on the LCD
(7) Press
- “COMMAND = -” is displayed on the LCD
Note:Steps 1 through 6 need to be completed within four (4) seconds.
TRF
CNF
*
TRF
CNF
#
ST
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							ND-46551 (E) CHAPTER 3
Page 145
Revision 2.0
NAP-200-010
Sheet 3/7
System Initialization and 
System Data Entr y
To reset CAT mode:
While “COMMAND = -” is displayed on the LCD:
(1) Lift the handset (off hook)
- SPKR lamp turns off.
(2) Restore the handset (on hook)
- CNF, ANS lamps turn off.
- LCD returns to clock.
2.2 MAT
In addition to the CAT mode programming, the MAT can also be used in the MAT mode.  Refer to the MAT Oper-
ation Guide and the Command Manual.
2.3 Feature Programming
This section provides the feature programming (Music On Hold, Push Button Calling) related to the internal PB Re-
ceiver and internal TNT on the MP card. For the other feature programming, refer to the Feature Programming Man-
ual.
In the programming procedure, the meaning of (1), (2) and marking are as follows:
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking ( ) is automatically assigned
for each command.
: System Initialization
After entering the data, system initialization is required (Depress SW1 of MP card).
INITIAL
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							CHAPTER 3 ND-46551 (E)
Pag e 1 46
Revision 2.0
NAP-200-010
Sheet 4/7
System Initialization and 
System Data Entr y
(1) Programming Procedure for Music On Hold
For providing Hold Tone Source on the MP card:
For providing External Hold Tone Source through the MP card:
DESCRIPTION DATA
Select the music to be provided. (1) 183
(2) 0: Nocturne
1 : Minuet
Define the type of call to be provided with Hold Tone 
on the MP card.
Note:When using the MP card, set the JP1
switch to UP (Internal Hold Tone Source)..Y = 0
(1) 00: C.O. Line Call
01: Tie Line Call
02: Internal Call
(2) 1400: Hold Tone Source on MP card
DESCRIPTION DATA
Define the type of call to be provided with Hold 
Tone..Y = 0
(1) 00: C.O. Line Call
01: Tie Line Call
02: Internal Call
(2) 1400: Hold Tone Source through MP cardSTART
CM08
CM48
END
START
CM48
END 
						

							ND-46551 (E) CHAPTER 3
Page 147
Revision 2.0
NAP-200-010
Sheet 5/7
System Initialization and 
System Data Entr y
For providing External Hold Tone Source through MP card:
• External Hold Tone Source provided locally
For connecting the External Hold Tone Source, plug the cable into JACK on the MP card.
Set the switches on the MP card as follows:
For providing Hold Tone Source on the MP card: Set the JP1 switch to UP.
PBX
MP CARD
JACKEXTERNAL HOLD TONE SOURCE
JP1
VR
MP CARD
JP1: INTERNAL/EXTERNAL
HOLD TONE SOURCE
VR: VARIABLE RESISTOR FOR
EXTERNAL HOLD TONE SOURCE
(0-20k
W: CLOCKWISE)
UP:
DOWN: EXTERNAL HOLD
TONE SOURCE INTERNAL HOLD
TONE SOURCE
: POSITION TO BE SET
20
0 
						

							CHAPTER 3 ND-46551 (E)
Pag e 1 48
Revision 2.0
NAP-200-010
Sheet 6/7
System Initialization and 
System Data Entr y
(2) Programming Procedure for Push button Calling
DESCRIPTION DATA
Assign the Card Number of internal PB Receiver to 
the LEN No. 0124.
Note:When using the internal PB Receiver on
the MP card, assign the Card No. E200-
E203 to the LEN No. 0124.
If resident load is used, PB Receiver ports
(E200-LENS 0124) are automatically as-
signed.(1) LEN: 0124
(2) E200-E203 (PB Receiver No.)
Assign the type of telephone set (DTMF) to DTMF 
Stations.
This data assignment is not required for Multiline 
Terminal station..YY = 00
(1) X-XXXX (Station No.)
(2) 2 : DTMF Telephone set
Assign PB Receivers for use with DTMF 
Stations..Y = 0 (Make Busy)
(1) XX X 
(2) :Make Busy Cancel
.Y = 1 (Purpose)
(1) XXX (Ditto to Y = 0)
(2) 1 :For both DTMF station and Tie Line/
DIDSTART
CM10
A
CM12
CM45INITIAL
Circuit No. 0-3
Card No. 00-03 assigned by
CM10(E200-E203)