NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 6 4
Revision 2.0
ATTENDANT CONSOLE (SN610): INCOMING CALL IDENTIFICATION
PROGRAMMING 
Refer to Attendant Called/Calling Number, Attendant Call Selection, Attendant Source Key, Attendant Listed Di-
rected Number, and Common Route Indial. 

ND-45670 (E) CHAPTER 2
Page 65
Revision 2.0
ATTENDANT CONSOLE (SN610): INDIVIDUAL TRUNK ACCESS
PROGRAMMING 
DESCRIPTION DATA
Assign the access code for Direct Trunk 
Selection.• Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX (Access Code) 
(2) 081
Assign the Trunk identification code to each 
trunk. 
The Trunk ID code is to be dialed after the 
access code, and displayed on the SN610 
ATTCON. • YY = 19
(1) Trunk No. (000-255) assigned by CM10 
(D000-D255)
(2) XXXX
:  Trunk ID code Note
*a: Set any desired...

CHAPTER 2 ND-45670 (E)
Pag e 6 6
Revision 2.0
ATTENDANT CONSOLE (SN610): MULTIPLE CONSOLE OPERATION
PROGRAMMING
Refer to ATTENDANT CONSOLE (SN610 ATTCON). 

ND-45670 (E) CHAPTER 2
Page 67
Revision 2.0
ATTENDANT CONSOLE (SN610): MULTI-FUNCTION KEY
PROGRAMMING
DESCRIPTION DATA
Provide each SN610 ATTCON Multi-
Function key capability.• YY = 17
(1) X: ATTCON No. (0-7) assigned by 
CM10
(2) 1 : Ineffective/Effective
Assign the required Multi-Function keys the 
each SN610 ATTCON.
Note 1:The following data is assigned as
initial data or resident data.
Note 2:When setting or canceling a group of
stations in DND/RC, ATTCON
Status No. 00 should be used.
Note 3:For the...

CHAPTER 2 ND-45670 (E)
Pag e 6 8
Revision 2.0
ATTENDANT CONSOLE (SN610): PUSHBUTTON CALLING-ATTENDANT
PROGRAMMING
DESCRIPTION DATA
Assign the type of signaling (DTMF) to 
Outgoing and Bothway Trunk Routes.• YY = 01 
(1) Trunk Route No. (00–63)
(2) 7CM35
END
START 

ND-45670 (E) CHAPTER 2
Page 69
Revision 2.0
ATTENDANT CONSOLE (SN610): SERIAL CALL
PROGRAMMING
DESCRIPTION DATA
Assign the SERIAL CALL SET and SERIAL 
CALL Keys on the SN610 ATTCON.• YY = 00 
(1) ATTCON No. +   + Key No. 
(2) F6062: Serial Call Termination
F6105: Serial Call SetCM90 START
END
, 

CHAPTER 2 ND-45670 (E)
Pag e 7 0
Revision 2.0
ATTENDANT CONSOLE (SN610): TRUNK GROUP BUSY DISPLAY
PROGRAMMING
HARDWARE REQUIRED
To provide the Trunk Group Busy Lamps on Attendant Console: 
SN610 ATTCON and PN-2DLCC card
To provide the Trunk Group Busy Lamps externally:
PN-DK00 card and lamp indicator provided by the customer.
DESCRIPTION DATA
Assign the Trunk Group No. to each trunk. 
Several trunks may be assigned to one Trunk 
Group Number.•  YY = 09
 (1)  000-255 (Trunk No.)
 (2)  01-62 (Trunk Group...

ND-45670 (E) CHAPTER 2
Page 71
Revision 2.0
ATTENDANT CONSOLE (SN610): UNSUPERVISED TRUNK-TO-TRUNK 
TRANSFER BY ATTENDANT
PROGRAMMING
Note:The trunk associated with at least one side of the call must be programmed for answer and/or release
signal(s) to ensure the trunks do not lock up. Refer to TRUNK-TO-TRUNK CONNECTION for data to be
assigned to each trunk.
DESCRIPTION DATA
Provide the system with this feature. (1) 206
(2) 1 : AvailableCM08 START
END 

CHAPTER 2 ND-45670 (E)
Page 72 Addendum-002
Revision 2.2 JANUARY, 1999
ATTENDANT CONSOLE (SN716 DESKCON)
PROGRAMMING
DESCRIPTION DATA
Assign the card number of the interface cir-
cuit for the SN716 DESKCON to its associ-
ated LEN. (1) 0000-0511 : LEN No.
(2) E000-E007 : ATTCON No.
Set the terminating system for the incoming
calls to SN716 DESKCON.•  YY=02 (Day mode), YY=03 (Night 
mode)
(1)  Trunk No. (000-255)
(2)  14: Termination to SN716 DESKCON
Assign the required Attendant Call Selection
keys and...

ND-45670 (E) CHAPTER 2
Page 73
Revision 2.0
ATTENDANT CONSOLE (SN716 DESKCON)
DESCRIPTION DATA
Key No.DataDescription  
13 F6000 C.O. Incoming 0 (LDN)
14 F6040 Tie Line Incoming 0 (TIE0)
15 F6064 Call Fowarding-Busy Line 
Incoming Indication
(BUSY)
16 F6060 Operator Call (ATND)
17 F6063 Call Forwarding-No Answer
Incoming Indication
(NANS)
18 F6061 Recall (Recall)
19 F6200 Source (SRC)
20 F6201 Destination (DEST)
22 F6203 Talk (Talk)
23 F6204 Hold (Hold)
24 F6202 Cancel (Cancel) 
25 Answer (Answer) 
26...