NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 1 14
Revision 2.0
BACKGROUND MUSIC (BGM)
HARDWARE REQUIRED
External BGM Source (Up to 10 BGM Sources can be provided)
PN-4COT/PN-TNT card
External BGM Sources (FM, AM Radio, Tape-Deck etc.) should be provided by the customer. Make the following
connections between BGM Sources and interface trunks. For details, refer to the MDF cross connection for an Ex-
ternal Tone Source in the INSTALLATION PROCEDURE MANUAL.
For PN-4COT Card:
LTC 
CONNECTOR
MDF
NO.0 
TRK
NO.1 
TRK
NO.2...

ND-45670 (E) CHAPTER 2
Page 115
Revision 2.0
BACKGROUND MUSIC (BGM)
Set the switches within PN-TNT card according to the following table.
• Level Control of External BGM Source through JACK0/JACK1
No. 0 CIRCUIT (JACK0) No. 1 CIRCUIT (JACK1)
OUTPUT LEVEL SW-1 SW-2 OUTPUT LEVEL SW-3 SW-4
-10 dB OFF OFF -10 dB OFF OFF
-7 dB ON OFF -7 dB ON OFF
-4 dB OFF ON -4 dB OFF ON
-1 dB ON ON -1 dB ON ON
For PN-TNT card:
Plug the cable connected to the BGM Sources into JACK0 and JACK1 on PN-TNT card:
BGM SOURCE...

CHAPTER 2 ND-45670 (E)
Pag e 1 16
Revision 2.0
BOSS/SECRETARY CALLING
PROGRAMMING
To set up the Secretary Station with the Multiline Terminal:
DESCRIPTION DATA
Assign the Secretary Station to the required 
station number.•  YY = 12
(1)  X-XXXX (Primary Extension No. of 
Secretary)
(2) 0: Secretary Station
If the Boss’ station is a Single-Line Telephone 
with MW lamp, provide the Message Waiting 
service to the Boss’ station.•  YY = 03
(1)  X-XXXX (Boss Station No. )
(2)  0: To be provided
Assign the...

ND-45670 (E) CHAPTER 2
Page 117
Revision 2.0
BOSS/SECRETARY CALLING
To assign the Boss’ Station as a single-line telephone:
HARDWARE REQUIRED
ETJ-16DD-1/ETJ-24DS-1/DTP-32-1/DTP-32D-1 and DLC card.
DESCRIPTION DATA
Assign the destination of the call from the 
Boss’ station that has Message Waiting set.• YY = 15
(1) 00-63 (Tenant No.)
(2) X-XXXX (Secretary’s Station No.)
(3)
To provide Boss/Secretary Override, assign 
Service Restriction Class A for Call Waiting 
to the Secretary and Boss Stations.For...

CHAPTER 2 ND-45670 (E)
Pag e 1 18
Revision 2.0
BROKER’S CALL
PROGRAMMING
Refer to CALL HOLD feature. 

ND-45670 (E) CHAPTER 2
Page 119
Revision 2.0
CALL BACK
PROGRAMMING
DESCRIPTION DATA
Provide the system with the Single-Digit 
Feature Access Code while the calling station 
hears ringback tone/busy tone.(1)  156 (Ringback Tone)
(2) 0: Allowed
 
(1)  208 (Busy Tone)
(2) 0: Allowed
Assign Service Restriction Class (A) to the 
necessary stations.•  YY = 02
(1)  X-XXXX: Station No. 
(2) XX
 XX
*a: Service Restriction Class (A) (00-
15 )
Assign the Call Back feature to the Service 
Restriction Class (A)...

CHAPTER 2 ND-45670 (E)
Page 120 Addendum-002
Revision 2.2 JANUARY, 1999
CALLER ID CLASS (1500 Series Enhancement)
PROGRAMMING
1. Trunk Assignment for CALLER ID CLASS
DESCRIPTION DATA
Specify the Terminating System in Day Mode 
and Night Mode for incoming calls.• YY=02 (Day Mode) 
• YY=03 (Night Mode) 
(1) Trunk No. (000-255) 
(2) 02: Trunk Line Appearance
03: Trunk Line Appearance+TAS
04: Direct-In Termination
09: Automated Attendant
11: ATTCON+Trunk Line Appearance
13: TAS
14: Termination to ATTCON
16:...

ND-45670 (E) CHAPTER 2
Page 121
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
2. CALLER ID Receiver Assignment
DESCRIPTION DATA
Provide the system with MF Signaling. (1) 52 (MF Signaling)
(2) 0: To be provided
Assign a Slot Number to the CIR (CALLER 
ID Receiver) Trunk.(1) Slot No. (04-15) 
(2) 08: CIR Trunk (PN-4RSTC)
The slot number is given by the SENSE switch 
on the CIR Trunk.
Assign the MF Receiver trunk number to each 
circuit of the CIR Trunk.• YY=04 
(1) XX: MF Receiver Trunk No....

CHAPTER 2 ND-45670 (E)
Pag e 1 22
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
3. Memory Clear for CIR Trunk (PN-4RSTC Card)
Clearing all data in memory for calling number development is necessary before assigning the calling num-
ber development data by CMDC and CMDB.
Note:Before memory clear, set the SW1-1 to SW1-4 on the CIR Trunk to all ON (Make-busy) and after memory
clear, restore them to OFF.
If required, clear the partial memory using the commands shown in below.
Note:Before memory...

ND-45670 (E) CHAPTER 2
Page 123
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
4. CALLER ID Development Data Assignment
DESCRIPTION DATA
Assign the Development Table for the calling 
number sent from the network.•
(1)
(2)YY=00-63 (Trunk Tenant No.) 
Calling Number
0 : Development Table No.0 
1499: Development Table No.1499
Assign whether the Trunk Tenant No. is 
effective for developing the calling number, or 
not.•
(1)
(2)YY=30 
0 (Trunk Tenant No. Development) 
0 : Ignore actual Trunk Tenant...