NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 1 34
Revision 2.0
CALL FORWARDING: CALL FORWARDING-NO ANSWER
DESCRIPTION DATA
To apply this feature to incoming calls, set the 
trunk route combinations for Tandem 
Connection.
Note:For Resident System Programming,
refer to the Command Manual.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
• CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting method for Call 
Forwarding-No...

ND-45670 (E) CHAPTER 2
Page 135
Revision 2.0
CALL FORWARDING: CALL FORWARDING-DESTINATION
PROGRAMMING
DESCRIPTION DATA
Assign Service Restriction Class (A) to each 
station.• YY = 02
(1) X-XXXX: (Station No.)
(2) XX
XX
*a: Service Restriction Class (A)
(00-15 )
Assign this feature to Service Restriction 
Class (A) assigned by CM12 YY=02.•Y=15
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY=02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
Destination, Entry and Cancellation,...

CHAPTER 2 ND-45670 (E)
Pag e 1 36
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-ALL CALLS
PROGRAMMING
In addition to the programming for Call Forwarding-All Calls, do the following programming.
DESCRIPTION DATA
Specify the number of times a call can be call 
forwarded.(1) 14
(2) 01-05 [Number of times (One to five 
times)]
If no data is set, the default setting is 5.CM42
END
START 

ND-45670 (E) CHAPTER 2
Page 137
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-BUSY LINE
PROGRAMMING
In addition to the programming for Call Forwarding-Busy Line, do the following programming.
DESCRIPTION DATA
Specify the number of times a call can be call 
forwarded.(1) 14
(2) 01-05 [Number of times (One to five 
times)]
If no data is set, the default setting is 5.CM42
END
START 

CHAPTER 2 ND-45670 (E)
Pag e 1 38
Revision 2.0
CALL FORWARDING: MULTIPLE CALL FORWARDING-NO ANSWER
PROGRAMMING
In addition to the programming for Call Forwarding-No Answer, do the following programming.
DESCRIPTION DATA
Specify the timing for No Answer after 
second Call Forwarding.•Y = 0
(1) 46
(2) 01-30: 4 -120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36
seconds.CM41
END
START 

ND-45670 (E) CHAPTER 2
Page 139
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING - ALL CALLS
(1200 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-All
Calls-Outside, set “1” (Allowed) for
YY=00, YY=26 of CM15• CM12 YY=02 
[Service Restriction Class (A) (00-
15 )]
• CM15 YY=00 (Call Forwarding-All
Calls)
• CM15 YY=26 (Call Forwarding-All
Calls-Outside)
(1) XX: Service Restriction Class (A)...

CHAPTER 2 ND-45670 (E)
Pag e 1 40
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING - ALL CALLS
(1200 Series Enhancement)
DESCRIPTION DATA
Assign whether or not an extention can set 
Split Call Forwarding-All Calls-Outside by 
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the 
forwarded station during a Split Call 
Forwarding-All Calls-Outside.(1) 387
(2) 0: Split Call forwarding-All Calls-Out-
side...

ND-45670 (E) CHAPTER 2
Page 141
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-ALL CALLS
(1200 Series Enhancement)
Note:The operating procedure for Split Call Forwarding-All Calls is as follows:
CM78 is used to assign the destination forwarded when the destination No. 0-7 is specified.
Dial Destination No. X (0-9)
Dial Access Code for Split Call
Forwarding - All Calls.0: BLOCK No. 0
1: 1
2: 2
3: 3 Destination assigned by
4: 4 CM78.
5: 5
6: 6
7:BLOCK No. 7
8:Destination for Call Forwarding-All Calls...

CHAPTER 2 ND-45670 (E)
Pag e 1 42
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:To provide this feature, set “1”
(Allowed) for YY=11, YY=28, YY
=12, YY=29 of CM15.• CM12 YY = 02
[Service Restriction Class (A) 
(0015 )]
• CM15 YY = 11 (Call Forwarding-Busy 
Line)
• CM15 YY = 28 (Call Forwarding-Busy 
Line-Outside)
• CM15 YY=12 (Call Forwarding-Busy 
Line/-No...

ND-45670 (E) CHAPTER 2
Page 143
Revision 2.0
CALL FORWARDING: SPLIT CALL FORWARDING-BUSY LINE
(1200 Series Enhancement)
DESCRIPTION DATA
To apply this feature to incoming calls, set the
trunk route combinations for Tandem Connec-
tion.• CM35 YY=05
(1) Trunk Route No. (00-63)
Note
(2) 1 : Release Signal arriveNote
Note:
For Resident System Programming,
refer to the Command Manual.• CM36
(1) Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 
YY=05)
(2) 0: Allowed
Specify the setting...