NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 8 4
Revision 2.0
AUTHORIZATION CODE
2. In a system without an Application Processor (PN-AP01)
DESCRIPTION DATA
Designate the MP card for this feature. (1) 216: Designation of Processor for Au-
thorization Code
(2) 0: MP (PN-CP00) card
Specify whether Service Set Tone should be 
provided after dialing the access code for 
Authorization Code.(1) 362: Provision of Service Set Tone af-
ter dialing the access code.
(2) 0/1 : Not to be provided/To be provid-
ed
Assign the Class of...

ND-45670 (E) CHAPTER 2
Page 85
Revision 2.0
AUTHORIZATION CODE
Note:Up to 100 Authorization Codes combined with Forced Account Codes can be defined.
DESCRIPTION DATA
Define the purpose (Y = 1) and the temporary 
Class of Service (Y = 2-4) for each 
Authorization Code.• Y = 1 (Purpose of the Code)
(1) XX: Code Serial No. (00-99)
(2) 1: Authorization Code
• Y = 2 (Trunk Restriction Class)
(1) XX : Code Serial No. (00-99)
(2) X : Trunk Restriction Class (1-8) 
specified by CM35 YY = 51-68.
• Y = 3 [Service...

CHAPTER 2 ND-45670 (E)
Page 86 Addendum-002
Revision 2.2 JANUARY, 1999
AUTOMATED ATTENDANT
PROGRAMMING 
DESCRIPTION DATA
Assign the data for Automated Attendant to
the required trunks.
Note:
When providing a Night Message for
Automated Attendant, the 2nd An-
swering Message which is assigned
by CM49 YY=00, 2nd data 02XX is
used for the Night Message. In that
case, the 2nd data 08 of CM30
YY=30, 31 cannot be specified for
handling of Busy/Not Available Auto-
mated Attendant destination.• YY=02...

ND-45670 (E) CHAPTER 2
Addendum-002 Page 87
JANUARY, 1999 Revision 2.2
AUTOMATED ATTENDANT
DESCRIPTION DATA
• YY=33 (When YY=30, 31 is set to data 
08, and all DTMF Receivers are busy.)
(1) Trunk No. (000-255)
(2) 00 : Disconnection
01 : Forwarded to TAS Indicator
03 : Forwarded to SN610 ATTCON
15 : Disconnection
Assign the DTMF Receiver for only Automat-
ed Attendant, if desired.•Y=2
(1) XX
 X: DTMF Receiver No. 
Card No. 00-15 assigned by 
CM10 (E200-E215)
Circuit No. (0-3)
(2) 0: Only for Automated...

CHAPTER 2 ND-45670 (E)
Page 88 Addendum-002
Revision 2.2 JANUARY, 1999
AUTOMATED ATTENDANT 
DESCRIPTION DATA
Specify whether no Dial tone connection is re-
quired for the answering method assigned by
CM64 Y=0.•Y=2
(1) 06
(2) 0/1 : Without DT/With DT
Specify the ringing rate for an Automated At-
tendant Call.(1) 180
(2) 0/1 : 0.2 sec. ON-0.2 sec. OFF
0.2 sec. ON-0.2 sec. OFF
0.2 sec. ON-2 sec. OFF
/As per CM35 YY=33
Specify the process when a call is transferred
by an Automated Attendant to a predeter-...

ND-45670 (E) CHAPTER 2
Addendum-002 Page 89
JANUARY, 1999 Revision 2.2
AUTOMATED ATTENDANT
When the 1st and/or 2nd answering message is required: CM30 YY=30, 31, 2nd data 08/CM64 Y=0, 2nd data 02,
or Night Message is required: CM64 Y=2, 2nd data 02, do the following programming. The following steps are al-
ways required.
HARDWARE REQUIRED
For providing the first and/or second Answering Message/Night Message, Digital Announcement Trunk (PN-
2DATA) is required.
DESCRIPTION DATA
Assign a Digital...

CHAPTER 2 ND-45670 (E)
Pag e 9 0
Revision 2.0
AUTOMATIC CALL DISTRIBUTION (ACD)
PROGRAMMING
To activate ACD:
DESCRIPTION DATA
For each ACD Group, assign station numbers, 
one by one, in the order of hunting.
Note:Up to 60 stations can be assigned
into a single ACD group.
Example:For setting Station Numbers 200, 
201, 202 into one ACD Group.
1st Operation  (1) 200 
(2) 201
2nd Operation (1) 201
(2) 202
3rd Operation  (1) 202
(2) 200•Y = 0
(1) X-XXXX (Station No.)
(2) X-XXXX (Another Station No. to be...

ND-45670 (E) CHAPTER 2
Page 91
Revision 2.0
AUTOMATIC CALL DISTRIBUTION (ACD)
DESCRIPTION DATA
• Y = 6 (Tie Line Incoming Call)
(1) X-XXXX (Pilot Station No. of the ACD 
Group)
(2) 0/1 : Not to be provided/To be provid-
ed
• Y = 7 (DID Call)
(1) X-XXXX (Pilot Station No. of the ACD 
Group)
(2) 0/1 :Not to be provided/To be provid-
ed
• Y=B (Designation of the number of 
queuing in each ACD group)
(1) X-XXXX (Pilot Station No. of the ACD 
Group)
(2) 0/1 : To be provided (See CM42-16)/
Not to be provided...

CHAPTER 2 ND-45670 (E)
Pag e 9 2
Revision 2.0
AUTOMATIC CALL DISTRIBUTION (ACD)
DESCRIPTION DATA
Assign the ACD Busy-Out key on the 
Multiline Terminal, if required.• YY = 00
(1) Primary Extension No. +   + Key No.
(2) F0044: ACD Busy-Out
Assign the Release key on the Multiline 
Terminal, if required.• YY = 00
(1) Primary Extension No. +   + Key No.
(2) F1020: Release
Specify the processing for an incoming call 
when all ACD Stations are busy.(1) 212
(2) 0/1 : Busy Tone Connection/Queuing
Specify the...

ND-45670 (E) CHAPTER 2
Page 93
Revision 2.0
AUTOMATIC CALL DISTRIBUTION (ACD)
To provide ACD delay announcement:
DESCRIPTION DATA
Assign the Class of Service for Digital 
Announcement Trunk Access (Record/
Replay/Delete) to the required station.• CM12 YY=02
(1) X-XXXX: Station No.
(2) XX
XX 
*a 
*a:  Service Restriction Class (A) 
(00-15 )
• CM15 YY=33
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY=02
(2) 1 : Allowed
Assign the Digital Announcement Trunk 
Circuit No. to the required LEN....