NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 3 4
Revision 2.0
ANNOUNCEMENT SERVICE
To provide an Internal Recorded Message from a Digital Announcement Trunk (PN-2DATA) in place of Music On
Hold:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127:  Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031...

ND-45670 (E) CHAPTER 2
Page 35
Revision 2.0
ANNOUNCEMENT SERVICE
Note 6:A voice message in place of Music-On-Hold can be provided when a call has been placed on hold.
-Different messages can be programmed on a tenant basis.
- Different messages can be programmed, depending on the type of line (CO line, Tie line or station) on
Hold.
- More than one connection can be made to a Digital Announcement Trunk Circuit. Only the first connec-
tion can be assured of hearing the message from the beginning.
-...

CHAPTER 2 ND-45670 (E)
Pag e 3 6
Revision 2.0
ANNOUNCEMENT SERVICE
To provide the Night Announcement by Digital Announcement Trunk (PN-2DATA)
DESCRIPTION DATA
Assign each Digital Announcement Trunk 
Circuit No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511)
(2) EB000-EB127:  Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000-EB031
For PIM2/3: EB032-EB063 
For PIM4/5:...

ND-45670 (E) CHAPTER 2
Page 37
Revision 2.0
ANNOUNCEMENT SERVICE
Note 7:A voice message can be sent to incoming C.O. lines during night mode. 
- Different messages can be programmed on each C.O. line.
- The voice message can be programmed for day/night. 
- More than one connection can be made to a Digital Announcement Trunk Circuit. Only the first con-
nection can be assured of hearing the message from the beginning.
- Announcements may be programmed to be repeated from 4 to 120 seconds in four-second...

CHAPTER 2 ND-45670 (E)
Pag e 3 8
Revision 2.0
ANSWER KEY
PROGRAMMING
Note:An ANSWER key is initially assigned on each Multiline Terminal. 
HARDWARE REQUIRED 
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card.
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required Multiline Terminals. • CM12 YY = 02 
(1) X-XXXX:  Primary Extension No. 
(2) XX XX
 
*a: Service Restriction Class (B):  00-
15
• CM15 YY = 72 
(1) XX : Service Restriction Class (B) as-
signed by CM12...

ND-45670 (E) CHAPTER 2
Page 39
Revision 2.0
ATTENDANT-ASSISTED CALLING
PROGRAMMING
DESCRIPTION DATA
Assign the Access code for an operator call. • Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code (0) 
(2) 800 
Allocate the ATTCON Group No. to each 
SN610 ATTCON. • YY = 00
(1) 0-7:  ATTCON No. assigned by CM10. 
(2) 0-3:  ATTCON Group No. 
Assign the Master ATTCON within the 
ATTCON Group. • YY = 01
(1) 0-7:  ATTCON No.
(2) 0/1 :  Master/Sub
Specify the tenants to be handled by each ATT...

CHAPTER 2 ND-45670 (E)
Pag e 4 0
Revision 2.0
ATTENDANT CAMP-ON
PROGRAMMING
To reenter a Camped-On trunk from an Attendant before Automatic Recall (1200 Series Enhancement):
To display the busy station number and name on an Attendant Console when reentering a Camped-On trunk by de-
pressing the loop key (1200 Series Enhancement):
DESCRIPTION DATA
Specify the Camp-On Tone sent to busy 
station.(1) 068 
(2) 0 : Camp-on Tone is sent out only once.
1  :  Camp-on Tone is repeated at an 
interval of 4...

ND-45670 (E) CHAPTER 2
Page 41
Revision 2.0
ATTENDANT CONSOLE (SN610 ATTCON)
PROGRAMMING
DESCRIPTION DATA
Assign the card number of the interface circuit 
for the SN610 ATTCON to its associated 
LEN. (1) 0000-0511 : LEN No.
(2) E000-E007 : ATTCON No.
Set the terminating system for the incoming 
calls to SN610 ATTCON.• YY = 02 (Day mode), YY = 03 (Night 
mode)
(1) Trunk No. (000-255)
(2) 14:  Termination to SN610 ATTCON
Assign the required Attendant Call Selection 
keys and ATTCON Function keys to each...

CHAPTER 2 ND-45670 (E)
Pag e 4 2
Revision 2.0
ATTENDANT CONSOLE (SN610 ATTCON)
DESCRIPTION DATA
Note:
ANS or RLS keys can be assigned on
either 25 or 26 by CM60 YY = 15. 
Allocate the ATT Group No. to each SN610 
ATTCON.• YY = 00
(1) ATTCON No. (0-7)
(2) 0:  ATT GROUP 0
3:  ATT GROUP 3
Specify the Master SN610 ATTCON within 
the ATT Group assigned by YY = 00. • YY = 01
(1) ATTCON No. (0-7) 
(2) 0/1 :  Master/Sub
Specify the location of Answer (ANS) and 
Release (RLS) key. • YY = 15
(1) ATTCON No. (0-7)...

ND-45670 (E) CHAPTER 2
Page 43
Revision 2.0
ATTENDANT CONSOLE (SN610): ATTENDANT CALLED/CALLING NAME DISPLAY
PROGRAMMING 
DESCRIPTION DATA
Provide the system with the Name Display 
Service. (1) 255 
(2) 1 :  To be provided
Assign the access code for station user name 
entry, used from individual stations.• Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX:  Access Code (62) 
(2) A10 
Assign a Trunk Name Number to each Trunk 
Route. • YY = 03
(1) 00-63 : (Trunk Route No.) 
(2) 00 : Trunk Name No. 00
14 :...