NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 1 24
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
DESCRIPTION DATA
Specify the ringing tone for each calling 
number, if required.•
(1)
(2)YY=04 (Ringing Tone Assignment)
Development Table No.0-1499
0 : Depends on CM35 YY=33
1: Not used
2: Internal Ringing Tone
3: External Ringing Tone
Specify which is displayed on the LCD, when 
receiving both the calling number and the 
name from network on incoming call.•
(1)
(2)YY=05 (Calling Number/Name Display) 
Development...

ND-45670 (E) CHAPTER 2
Page 125
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
5. Other Relational Data Assignment
DESCRIPTION DATA
Assign the Trunk Access Code for outgoing 
call sent to the SMDR.
For using Save & Repeat feature, this Trunk 
Access Code will save and sent with the 
calling number.•
(1)
(2)YY=44
(Trunk Access Code for Save &Repeat) 
Trunk Route No. (00-63) 
X/XX : Trunk Access Code 0-9/00-99 
Specify whether the calling number is sent to 
the OAI Terminal or not.(1)
(2)462...

CHAPTER 2 ND-45670 (E)
Pag e 1 26
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
6. Data Assignment for multiple CIR Trunk
The development data by CMDC and CMDB are assigned toward the first CIR Trunk which has been as-
signed a minimum Slot Number. When providing multiple CIR Trunks, save the development data and load
them for the other CIR Trunks according to the following steps.
For detail of MAT operations, refer to the MAT Operation Guide.
STEP 1 After assignment of CMDC and CMDB, save the...

ND-45670 (E) CHAPTER 2
Page 127
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
STEP 12 Set the MB switch to ON (UP) on the third CIR Trunk with Slot Number Z.
STEP 13 As for the fourth CIR Trunk, change the Slot Number W to X 
by CM05 and by the SENSE switch.
STEP 14 Set the SW1-1 through SW1-4 to ON on the fourth CIR Trunk.
Clear the memory for CMDC and CMDB by CMDB YY=90.
Set the SW1-1 through SW1-4 to OFF on the 
fourth CIR Trunk.
STEP 15 Load the office data saved in STEP1 by MAT.
STEP 16 As...

CHAPTER 2 ND-45670 (E)
Pag e 1 28
Revision 2.0
CALLER ID DISPLAY
(1800 Series Enhancement)
PROGRAMMING
In addition to Automatic Number Identification (ANI) or Caller ID Class, assign the following data.
DESCRIPTION DATA
Provide the Multiline Terminal with a Caller 
ID Display key for displaying the ANI or 
Caller ID.•
(1)
(2)YY=00
Primary Extension No. +   + Key No.
F5010: Caller ID Display
START
END
CM90
, 

ND-45670 (E) CHAPTER 2
Page 129
Revision 2.0
CALL FORWARDING: CALL FORWARDING - ALL CALLS
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to
the required stations.
Note:When providing Call Forwarding-All
Calls-Outside, set “1” (Allowed) for
YY = 00, YY = 26 of CM15.•
•
•
(1)
(2)CM12 YY=02
[Service Restriction Class (A) (00-15 )]
CM15 YY=00 (Call Forwarding-All
Calls)
CM15 YY=26 (Call Forwarding-All
Calls-Outside)
XX: Service Restriction Class (A) 
assigned by CM12 YY=02.
1 :...

CHAPTER 2 ND-45670 (E)
Pag e 1 30
Revision 2.0
CALL FORWARDING: CALL FORWARDING - ALL CALLS
DESCRIPTION DATA
Specify the setting method for Call Forward-
ing-All Calls-Outside.(1)
(2)222
0: The feature is set when the station
goes on hook/when receiving Ser-
vice Set Tone (ORT time out)
1 : The feature is set when receiving
Service Set Tone (ORT time out)
Assign whether or not an extention can set
Call Forwarding-All Calls-Outside by enter-
ing only a trunk access code.(1)
(2)386
0: Restrict
1 : Allow...

ND-45670 (E) CHAPTER 2
Page 131
Revision 2.0
CALL FORWARDING: CALL FORWARDING-BUSY LINE
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-
Busy Line-Outside, set “1”
(Allowed) for YY = 11, YY = 28, YY
= 12, YY= 29 of CM15.•  CM12 YY = 02
[Service Restriction Class (A) (00-
15 )]
•  CM15YY = 11 (Call Forwarding-Busy 
Line)
•  CM15YY = 28 (Call Forwarding-Busy 
Line-Outside)
• CM15YY=12 (Call Forwarding-Busy 
Line/-No...

CHAPTER 2 ND-45670 (E)
Pag e 1 32
Revision 2.0
CALL FORWARDING: CALL FORWARDING-BUSY LINE
DESCRIPTION DATA
Specify the setting method for Call 
Forwarding-Busy Line-Outside.(1) 222
(2) 0: The feature is set when the station goes 
on hook/when receiving Service Set 
Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Allow or restrict the ability to set Call 
Forwarding-Busy Line for a station with Do 
Not Disturb set.(1) 240
(2) 0: Allow
1 : Restrict
Assign whether...

ND-45670 (E) CHAPTER 2
Page 133
Revision 2.0
CALL FORWARDING: CALL FORWARDING-NO ANSWER
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-No
Answer-Outside, set “1” (Allowed)
for YY=10, YY=27, YY=12, YY=29
of CM15• CM12YY = 02
[Service Restriction Class (A) (00-
15 )]
• CM15YY=10 (Call Forwarding-No An-
swer)
• CM15YY=27 (Call Forwarding-No An-
swer-Outside)
• CM15YY=12 (Call Forwarding-Busy 
Line/-No Answer)
•...