NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 1 84
Revision 2.0
CUSTOMER ADMINISTRATION TERMINAL (CAT)
PROGRAMMING
DESCRIPTION DATA
Assign the class of service for CAT to the 
required Multiline Terminals.• CM12 YY = 02 
(1) X-XXXX (Primary Extension No.)
(2) XX XX
 
*a: Service Restriction Class (B) 
(00-15 )
• CM15 YY = 56 
(1) XX: [Service Restriction Class (B) 
(00-15)] assigned by CM12 YY 
= 02.
(2) 1  Allowed
Specify the command codes accessible to 
each Password Level.• YY = 00: Password Level 0-6
• YY = 01:...

ND-45670 (E) CHAPTER 2
Page 185
Revision 2.0
CUSTOMER ADMINISTRATION TERMINAL (CAT)
Note 1:If the system data all clear or system data partial clear is required before programming from a CAT, per-
form the following operations:
1. Plug the PN-2DLCB/4DLCA card into LT00 Slot of PIM0 
2. Connect the CAT to LEN0000 at the MDF
3. Set SW3 on the MP card to “B”
4. Press SW1 (RESET Switch) on the MP card (System Data All Clear/Partial Clear)
5. Set SW3 to “0” and press SW1.
6. Set the Multiline Terminal to CAT...

CHAPTER 2 ND-45670 (E)
Pag e 1 86
Revision 2.0
DATA LINE SECURITY
PROGRAMMING
DESCRIPTION DATA
Assign the function of Analog Data Station 
(Single-Line Station with FAX or MODEM) 
to the required stations.• YY = 07
(1) X-XXXX (Station No.)
(2) 0: Data Station 
END
CM13 START 

ND-45670 (E) CHAPTER 2
Page 187
Revision 2.0
DELAYED RINGING
PROGRAMMING
DESCRIPTION DATA
Assign the Delayed Ringing feature to each 
line key on a Multiline Terminal.
Note:The Delayed Ringing feature can be
assigned to the first 16 line/trunk
keys (Key 01-16). • YY = 03
(1) Primary Extension No. +     + Key No.
Note
(2) 0: Delayed Ringing 
Specify the timing for Delayed Ringing.  • Y = 1
(1) 09
(2) 01-20: 2-40 sec. in 2 sec. increments
If no data is set, the default setting is 10
seconds.
END
CM90...

CHAPTER 2 ND-45670 (E)
Pag e 1 88
Revision 2.0
DIAGNOSTICS
PROGRAMMING
Refer to the Maintenance Manual. 

ND-45670 (E) CHAPTER 2
Page 189
Revision 2.0
DIAL CONVERSION
PROGRAMMING
DESCRIPTION DATA
Assign the Card Number of the DTMF 
Receiver to the required LENs.
Note:When using the internal DTMF Re-
ceiver on the PN-CP03 card, assign
the Card No. E200 to LEN No.
0124.(1) LEN (0000-0511)
(2) Card No. of DTMF Receiver
E200-E203: For PIM0/1 
E204-E207: For PIM2/3 
E208-E211: For PIM4/5 
E212-E215: For PIM6/7 
Assign the type of telephone set (DTMF) to 
DTMF Stations. This data assignment is not 
required for...

CHAPTER 2 ND-45670 (E)
Pag e 1 90
Revision 2.0
DIAL CONVERSION
DESCRIPTION DATA
For a DP trunk, assign the type of signaling 
for Outgoing and Bothway trunk routes to 
DP. 
Specify the DP Sender characteristics to 
match the Central Office.• YY = 01
(1) Trunk Route No. (00-63) 
(2) 2 
• YY = 23 (DP Sender Inter Digital 
Pause) 
(1) Trunk Route No. (00-63) 
(2) 0: 300 ms 
1: 400 ms 
2: 500 ms 
3: 600 ms 
4: 700 ms 
5: 900 ms 
6: 1100 ms 
7: 800 ms 
• YY = 25 (DP Sender Make Ratio) 
(1) Trunk Route No....

ND-45670 (E) CHAPTER 2
Page 191
Revision 2.0
DIAL CONVERSION
HARDWARE REQUIRED 
DTMF Receiver (PN-8RST) ´ n 
n: Depends on the number of DTMF stations and the traffic condition of the system.
DESCRIPTION DATA
Specify the DTMF Sender characteristics to 
match the Central Office.• YY = 24 (DTMF Inter Digital Pause) 
(1) Trunk Route No. (00-63)
(2) 0: 32 ms 
1: 64 ms 
2: 80 ms 
3: 96 ms 
4: 160 ms 
5: 192 ms 
6: 240 ms 
7: 128 ms
• YY = 26 (DTMF Sender Signal Width) 
(1) Trunk Route No. (00-63)
(2) 0/1: 64...

CHAPTER 2 ND-45670 (E)
Pag e 1 92
Revision 2.0
DIRECT DIGITAL INTERFACE
PROGRAMMING
Refer to the DDI System Manual. 
HARDWARE REQUIRED 
Refer to the DDI System Manual.  

ND-45670 (E) CHAPTER 2
Page 193
Revision 2.0
DIRECT INWARD DIALING (DID)
PROGRAMMING
DESCRIPTION DATA
Assign the ring rate on a DID call.  (1) 180
(2) 0/1: 0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec. ON, 0.2 sec. OFF, 0.2 sec. 
ON, 0.2 sec. OFF/As per the data 
of CM35 YY = 33
Assign the Trunk Numbers to the required 
LENs.(1) LEN (0000-0511) 
(2) Trunk No. (D000-D255)
Assign the data for DID to the Trunk 
Numbers assigned by CM10.• YY = 00 (Trunk Route Allocation)
(1) Trunk No. (000-255)
(2) Trunk Route No....