NEC Neax2000 Ivs Feature Programming Manual

CHAPTER 2 ND-45670 (E)
Pag e 2 04
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
Note 1:Up to 1,000 Direct Inward System Access (DISA) codes combined with Authorization Codes and Forced
Account Codes can be defined. 
Note 2:When deleting all ID codes stored in the PN-AP01 card at one time, do the following operation:
 + D60 +   + 0000 +   + CCC +  
HARDWARE REQUIRED 
PN-AP01 card ´ 1 (If 1,000 codes and/or Check Code is provided.)
PN-2DATA card x n (n = 1-128) (If a Digital Announcement Trunk is...

ND-45670 (E) CHAPTER 2
Page 205
Revision 2.0
DIRECT INWARD TERMINATION (DIT)
PROGRAMMING 
DESCRIPTION DATA
Assign the data for terminating system in Day 
Mode and Night Mode, to each Loop/Ground 
Start trunk, respectively. • YY = 02 (Day Mode)/YY = 03 (Night 
Mode)
(1) Trunk No. (000-255)
(2) 04: Direct-In Termination
Assign the station number to be terminated by 
DIT in Day Mode and Night Mode 
respectively.• YY = 04 (Day Mode)/YY = 05 (Night 
Mode)
(1) Trunk No. (000-255)
(2) X-XXXX: Station No.
Assign...

CHAPTER 2 ND-45670 (E)
Pag e 2 06
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
PROGRAMMING
DESCRIPTION DATA
Assign the Trunk Numbers to the required 
LENs.(1) LEN (0000-0511) 
(2) Trunk No. (D000-D255)
Assign the data for Direct Outward Dialing to 
the Trunk No. assigned by CM10. 
Note:For Resident System Program, refer
to the Command Manual. • YY = 00 (Trunk Route Allocation) 
(1) Trunk No. (000-255)
(2) Route No. (00-63) Note
 
• YY = 01 (Tenant Allocation)
(1) Trunk No. (000-255)
(2) Tenant No. (00-63)...

ND-45670 (E) CHAPTER 2
Page 207
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
DESCRIPTION DATA
Assign the data for Direct Outward Dialing to 
the Route No. assigned by CM30 YY = 00. 
Note:For Resident System Program, refer
to the Command Manual. • YY = 00 (Kind of Route)
(1) Trunk Route No. (00-63)
(2) 00: DDD 
01: FX
02: WATS
03: CCSA
• YY = 01 (Type of Signal) 
(1) Trunk Route No. (00-63) 
(2) 2: DP
4: DTMF 
• YY = 02 (OG/IC) 
(1) Trunk Route No. (00-63)
(2) 2 : Outgoing 
3:Bothway 
• YY = 04 (Answer...

CHAPTER 2 ND-45670 (E)
Pag e 2 08
Revision 2.0
DIRECT OUTWARD DIALING (DOD)
Note:For the Trunk Restriction Class, refer to Class of Service Individual.
DESCRIPTION DATA
According to the characteristics of each C.O. 
line, assign the data for DP/DTMF Sender to 
each route. 
For the details of the command, refer to the 
Command Manual.
Note:For Resident System Program, refer
to the Command Manual. • YY = 20 (Sender Start Condition) 
• YY = 21 (Sender Prepause Timing) 
• YY = 23 (DP-Inter Digital Pause) 
•...

ND-45670 (E) CHAPTER 2
Page 209
Revision 2.0
DIRECT STATION SELECTION/BUSY LAMP FIELD (DSS/BLF) CONSOLE
PROGRAMMING
HARDWARE REQUIRED 
DSS Console 
PN-2DLCB/4DLCA card (Two or four DSS Consoles can be accommodated per card) 
DESCRIPTION DATA
Assign the DSS Console Number to its 
associated LEN.(1) 0000-0511 (LEN)
(2) DSS Console No. 
E100-E107: For PIM0/1 
E108-E115: For PIM2/3 
E116-E123: For PIM4/5 
E124-E131: For PIM6/7 
Assign a single-line station, Multiline 
Terminal, or SN610 ATTCON to work in...

CHAPTER 2 ND-45670 (E)
Pag e 2 10
Revision 2.0
DISTINCTIVE RINGING
PROGRAMMING
DESCRIPTION DATA
Select the ringing pattern on an internal and 
Direct-In Termination Call, Direct Inward 
Dialing, DISA, and Automated Attendant. (1) 138 (For Internal)
(2) 0/1: 2 sec. ON, 4 sec. OFF/1 sec. 
ON, 2 sec. OFF. 
(1) 179 (For DIT Call)
(2) 0/1: As per CM35 YY = 33/0.4 sec. 
ON, 0.2 sec. OFF, 0.4 sec. ON, 2 
sec. OFF. 
(1) 180 (For DID, DISA and Automated 
Attendant) 
(2) 0/1:0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec....

ND-45670 (E) CHAPTER 2
Page 211
Revision 2.0
DISTINCTIVE RINGING
To provide a distinctive lamp indication for Multiline Terminals during a call termination, do the following program-
ming:
DESCRIPTION DATA
Specify the lamp color for an incoming 
external call. 
Note:The lamp color for incoming inter-
nal calls is red (120 IPM flashing).
For indicating the termination of a
transferred external incoming call,
the flashing lamp color depends on
CM08-137. • YY = 32
(1) Trunk route number (00-63) 
(2) 0/1:...

CHAPTER 2 ND-45670 (E)
Pag e 2 12
Revision 2.0
DO NOT DISTURB
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for Do Not 
Disturb to the required stations.• CM12 YY=02: Service Rest. Class (A)
(00-15t)
• CM15 YY=19
(1) Service Rest. Class (A) (00-15) assigned 
by CM12 YY=02
(2) 1 : Allowed
Assign the group of stations in Do Not 
Disturb. Do Not Disturb is set to these stations 
(assigned by this command) simultaneously 
by operation from an Attendant Console.• YY=00
(1) X-XXXX (Station No.)
(2)...

ND-45670 (E) CHAPTER 2
Page 213
Revision 2.0
DO NOT DISTURB
DESCRIPTION DATA
Specify the Call Forwarding-Busy Line/
Station Hunting for a station set for Do Not 
Disturb.240 
0: Available 
1 : Not Available
For a system using multiple tenants, specify 
for which tenant (the calling or called station) 
the assignment refers to CM51 YY=10. CM51 
YY=10 determines the destination to which a 
call is transferred when the called station is in 
Do Not Disturb.241 
0:  Tenant of called station 
1 :  Tenant of...