NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 57
Alert Service A-57
A-57 Alert Service
General Description
In an emergency situation, the Console or Special Administration Station may initiate the ALERT SERVICE. All
guest stations and Special Administration Stations are called, using a distinctive ringing pattern, and connected to
an emergency announcement.
At this time, if D
terms are used for guest stations, the Dterm LCDs will indicate emergency.
Operating Procedure
To set...

NEAX2400 IMX Hotel Feature Programming Manual
Page 58ND-70284 (E), Issue 2
A-57 Alert Service
Operating Procedure (cont’d)
Note:
On answering, the station is automatically connected to an announcement machine. If Language service has been
specified by PMS, the guest will receive the announcement in their own language.
Service Conditions
1. A guest station is called every 2 seconds, to a maximum of 24 stations per Module Group ringing
simultaneously. The stations are called in ascending order, based on...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 59
Alert Service A-57
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
161b
0Don’t Disturb Override key on Console
0/1 = Out/In Service
b
1Message Waiting Lamp in Service
0/1 = Out/In Service
b
2Language Service
0/1 = Out/In Service
b
3Split Hold Service
0/1 = Out/In Service
b
4Not used
b
5DSS (Direct Station Section) Key on Console
0/1 = Ineffective/Effective
b
6Timing Start using “#” Code
0/1 =...

NEAX2400 IMX Hotel Feature Programming Manual
Page 60ND-70284 (E), Issue 2
A-57 Alert Service
3SYS1
ASYD
INDEX
183b
0
Designation of the Hotel/Motel Console that sets Alert Service
0: Service can be set from any of the Console
1–15: Service can be set only from the Console of the designated Console Number b1
b2
b3
b4
Classifying the call termination indicating keys on the basis of the Language category of the 
guest at the time an incoming call from a guest station has terminated to the Hotel/Motel...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 61
Automatic Wake-up – Hotel Attendant A-58
A-58  Automatic Wake-up – Hotel Attendant
General Description
When AUTOMATIC WAKE-UP [A-10] is set to the guest station with VIP status and it is time for the guest to be
awakened, the call will ring the Console. When answered, the call is extended to the guest. The guest will be greeted
by the attendant rather than a recorded announcement.
Operating Procedure
To operate from the...

NEAX2400 IMX Hotel Feature Programming Manual
Page 62ND-70284 (E), Issue 2
A-58 Automatic Wake-up – Hotel Attendant
Service Conditions (cont’d)
4. If the guest station goes off-hook after the Attendant presses the WKUP key, but before the Attendant
presses the START key, the guest and Attendant will be connected.
5. The system reports the Wake-Up call as “called” at the time it rings in at the WKUP key. 
6. An incoming Wake-Up call to the Console that is not answered will not time out. The system will...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 63
Automatic Wake-up – Hotel Attendant A-58
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
165b
0Port Number accommodating the Hotel Printer Command Service
b
1
b2
b31: Hotel Printer in service
b
4Automatic Wake-Up-Hotel Attendant Assistant
0/1 = Out/In Service
b
5Setting the priority for Guest Station in Automatic Wake-Up
0/1 = Out/In Service
b
6Wake-Up information (time, station number, etc.) printout
0/1 =...

NEAX2400 IMX Hotel Feature Programming Manual
Page 64ND-70284 (E), Issue 2
A-73 Automatic Multiple Attendant Recall
A-73 Automatic Multiple Attendant Recall
General Description
This feature is a variation of the Automatic Recall feature of the NEAX2400 IMX. When the Attendant answers an
incoming trunk call, dials the station, and presses the RELEASE key, the automatic-recall timer is activated. The
dialed station rings, but if it is unanswered within the customer-defined recall time, the call is directed...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 65
Automatic Multiple Attendant Recall A-73
Service Conditions (cont’d)
9. CALL FORWARDING – DONT ANSWER [C-3] supersedes this feature.
10. This feature can be used in conjunction with CALLED NUMBER DISPLAY – ATTENDANT [C-59]. If
CALLED NUMBER DISPLAY – ATTENDANT [C-59] is activated, the called station number is
displayed on the console when the Attendant answers. (The called number is displayed not only by
AUTOMATIC MULTIPLE...

NEAX2400 IMX Hotel Feature Programming Manual
Page 66ND-70284 (E), Issue 2
A-74 Answering Camp-On/Call Hold Calls By Switchhook Flash
A-74   Answering Camp-On/Call Hold Calls By 
Switchhook Flash
General Description
This feature allows a busy guest station to answer a CAMP-ON or CALL HOLD call automatically by using switch
hook flash.
Operating Procedure
To answer a CAMP-ON call:
To answer a CALL HOLD call:
Step Action Result
1
The Attendant executes ATTENDANT 
CAMP-ON WITH TONE INDICATION [A-
1].A...