NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 47
Attendant Console With Hotel Functions A-25
8SYS1
ASYD
INDEX 
257b
0DLKC Circuit Card for Console
0/1 = Not exist in system/Exist in system (for NEAX2400 IMX, 4 IMG system only)
b
1
Not used b
2
b3
b4
b5
b6
b7
9SYS2
ASYD
INDEX 
0b
0
Restriction Data of Station Busy Services can be designated as the table below:
R: Restricted A: Allowed
b1
b2Not used
b
3Attendant Override service
0/1 = Out/In Service
b4Busy Verification (Console)...

NEAX2400 IMX Hotel Feature Programming Manual
Page 48ND-70284 (E), Issue 2
A-25 Attendant Console With Hotel Functions
10SYS2
ASYD
INDEX
 2b
0Sender Signal to DP/PB Route (Station)
0/1 = DP/PB
b
1Sender Signal to DP/PB Route (Console)
0/1 = DP/PB
b2
Console Day/Night Mode Change
b
3
b4Not used
b
5Attendant Loop Release service 
0/1 = Out/In Service
b
6Not used
b
7Kind of DP sender (when b0 = 0)
0/1 = 10 PPS/20 PPS
11SYS2
ASYD
INDEX 
6b
0Message Center Interface service when terminating to a UCD Group
0/1...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 49
Attendant Console With Hotel Functions A-25
13SYS2
ASYDINDEXES 
8 & 9Call Waiting Display on Console
14SYS2
ASYD
INDEX 
14b
0
CW Lamp on Console-Threshold
CW Lamp flashes when the number of Calls Waiting is greater than or equal to this 
data.
b
1
b2
b3
b4Calls that activate CW Lamp Flash
0/1 = All Calls/Only the types of Calls specified in SYS2, INDEXes 8 and 9
b
5
Not used b6
b7
15AHSY
INDEX 
105b
0Not used
b
1
b2Maid Dial...

NEAX2400 IMX Hotel Feature Programming Manual
Page 50ND-70284 (E), Issue 2
A-25 Attendant Console With Hotel Functions
18AHSY 
INDEX 
183b
0
Setting of Hotel/Motel Console that sets Alert Service
0 Hex: Service can be set from any of the Console
1–F Hex: Service can be set only from the Console of the designated Console Number b1
b2
b3
b4
Classifying the call termination indicating keys on the basis of the Language 
category of the guest at the time an incoming call from a guest station has terminated...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 51
Attendant Console With Hotel Functions A-25
Table 4  Key Arrangement for Hotel Attendant Console
Data
Key Arrangement Remarks
b
4b3
00
WUS: Wake Up Set
WUR: Wake Up Reset
DDS: Do Not Disturb Set
DDR: Do Not Disturb Reset
MWS: Message Waiting Set
MWR: Message Waiting Reset
RCS: Room Cutoff Set
RCR: Room Cutoff Reset
AUD: Audit Report
STS: Status Check
C/I: Check-In
C/O: Checkout
SCS: Boss-Secretary Set
SCR: Boss-Secretary Reset...

NEAX2400 IMX Hotel Feature Programming Manual
Page 52ND-70284 (E), Issue 2
A-26 Audit Reports
A-26 Audit Reports
General Description
The System provides AUDIT REPORT printout of all rooms assigned specific Room Status conditions. For
example, an AUDIT of all stations in DO NOT DISTURB [D-11] mode may be ordered. These REPORTS are
generated by key operation and function codes entered from the Hotel Console. AUDIT REPORTS available from
the printer are as follows:
Function
Printout Information
Code...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 53
Audit Reports A-26
Operating Procedure
To order AUDIT REPORTS printouts from the Console or Front Desk Terminal:
Service Conditions
1. VIP classification must be entered via PMS.
2. Room classifications are assigned via the MAT.
3. Guest name and optional data (Language, etc.) are displayed on the Console, but are not included in the
printout.
4. Hotel printer is necessary for this service feature.
5. Only one audit may be run...

NEAX2400 IMX Hotel Feature Programming Manual
Page 54ND-70284 (E), Issue 2
A-26 Audit Reports
2SYS1
ASYD
INDEX
168b
0Group Announcement Service (for Hotel system)
0/1 = Out/In Service
b
11: Audit Report in service
b
2Not used
b
3
b4Off-Hook Alarm (Service)
0/1 = Out/In Service
b
5Destination for Off-Hook Alarm Termination
0/1 = Console/Station
b
6Destination for Priority Call Termination
0/1 = Console/Station
b
7Not used
STEP CMND EXPLANATION
3 AIOC Assign printer port to match SYS1, ASYD, INDEX 11, in...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 55
Automatic Message Waiting Lamp Off A-48
A-48  Automatic Message Waiting Lamp Off
General Description
This feature provides for guest station MESSAGE WAITING [M-6] lamps to automatically turn off after guests
have called predetermined Administration Stations (i.e. Message Center) to retrieve messages.
Operating Procedure
When a guest calls the Administration Station to retrieve a message, the MESSAGE WAITING [M-6] lamp on the...

NEAX2400 IMX Hotel Feature Programming Manual
Page 56ND-70284 (E), Issue 2
A-48 Automatic Message Waiting Lamp Off
STEP CMND BIT EXPLANATION
2SYS1
ASYD
INDEX 
172b
0Message Waiting
Data transfer to/from PMS 
when executing the service.
0/1 = Not to be executed/ To 
be executed.
b1Message Registration
b
2Do Not Disturb, Room Cutoff
b
3Room Status
b
4Automatic Wake-Up, Group Announcement
b
5Room Change, Room Swap
b
6Room Data Change
b
7Not used
3SYS1
ASYD
INDEX 
179b
0Ringing Duration for Automatic...