NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 97
Do Not Disturb - DtermD-11D
Service Conditions (cont’d)
5. If a call to a station in DO NOT DISTURB mode is routed to the Console, the Attendant may be able to
connect both stations for temporary service cancellation by pressing the DND OVER key. This aspect of
the DO NOT DISTURB feature is programmable into system data.
6. DO NOT DISTURB is provided for guest room stations only.
7. When a station in a suite sets DO NOT DISTURB,...

NEAX2400 IMX Hotel Feature Programming Manual
Page 98ND-70284 (E), Issue 2
D-11D Do Not Disturb - Dterm
2SYS1
ASYD
INDEX 
161b
0Do Not Disturb Override key on Console
0/1 = Out/In Service
b
1Message Waiting Service
0/1 = Out/In Service
b2Language Service
0/1 = Out/In Service
b3Split Hold Service
0/1 = Out/In Service
b
4Not used
b
5DSS (Direct Station Section) Key on Console
0/1 = Ineffective/Effective
b
6Timing Start using “#” Code
0/1 = Ineffective/Effective
b
7Timing Start using “*” Code
0/1 =...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 99
Do Not Disturb - DtermD-11D
4SYS1
ASYD
INDEX
170b
0Room status data (b2, b1, b0) to be set at the time of Checkout
Note:
Do not assign other data. b
1
b2
b3
Assignment of Restriction Method in Do Not Disturb Status
0/1 = Restricted/Restriction Method according to RSC
Note:
If unconditional restriction is set as per the OG restriction and IC restriction
information, or if OG restriction and IC restriction are set to guest...

NEAX2400 IMX Hotel Feature Programming Manual
Page 100ND-70284 (E), Issue 2
D-11D Do Not Disturb - Dterm
6AHSY
INDEX
77b
0LCD Indication of Wake-Up time on the Dterm
 0/1 = -/Remains lit
b
1LCD Indication of “DD” (Do Not Disturb) on the Dterm
 0/1 = -/Remains lit
b
2LCD Indication of “RC” (Room Cutoff) on the Dterm
 0/1 = -/Remains lit
b
3LCD Indication of 2nd Wake-Up time on the Dterm
b4
Not used b5
b6
b7
7AHSY
INDEX
266b
0Not used
b
1
b2Room Cutoff and Do Not Disturb
(Feature Code = 15, Function Code =...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 101
Do Not Disturb - DtermD-11D
11 ARSC When “1” has been assigned by SYS1, INDEX 170, Bit 3, assign restriction data to RSC 14 and 15.
Note:
Steps after ARTD are necessary only when the destination of the tone of Do Not Disturb call is designated as
Announcement Machine.
12 ARTDAssign the route data of the trunk which interfaces with the announcement unit (OSGS = 2, TCL = 
4 should be set without fail).
13 ATRK Assign the trunk...

NEAX2400 IMX Hotel Feature Programming Manual
Page 102ND-70284 (E), Issue 2
D-15 Day/Night Class of Service
D-15   Day/Night Class of Service
General Description
This feature permits all stations within a tenant to alternate between two different CLASS OF SERVICE –
INDIVIDUAL [C-15] options, one for Day mode and another for Night mode. System data can be programmed so
that once the ATTENDANT CONSOLE [A-3] has entered the NIGHT CONNECTION [N-1, 2] mode, a stations
CLASS OF SERVICE – INDIVIDUAL [C-15] will...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 103
Day/Night Class of Service D-15
Assignment Procedure 
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 75b
0Route Restriction Class Data (“ARSC” command)
0/1 = Common/Separate
Table Development:
Common or Separate Day/
Night Data Tables.
Note:
When data tables are 
designated as 
“Common”, the Day 
mode designation 
must be used in the 
respective 
commands. b
1
Service Feature Restriction Class Data (“ASFC” 
command)
0/1 =...

NEAX2400 IMX Hotel Feature Programming Manual
Page 104ND-70284 (E), Issue 2
D-15 Day/Night Class of Service
5 ATDP Assign Day/Night data.
6 ATNR Assign Day/Night data.
7 AEFR Assign Day/Night data.
8 ASPF Assign Day/Night data.
9 ASCR Assign Day/Night data.
10 ATCR Assign Day/Night data. ATCR will override ASCR on restriction.
11 ADNRAssign the Time for Day mode and Night mode, if automatic change of Route Restriction Class 
(RSC) is necessary. STEP CMND EXPLANATION 

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 105
Direct Page Connection D-23
D-23   Direct Page Connection
General Description
This feature allows direct loop-to-loop connection for paging, enabling the Attendant to hold an incoming (IC) call,
page the desired party, then directly connect both parties after the paged party answers.
Operating Procedure
For IC call on a loop requiring paging:
To connect the held party to the paged party, (via HOUSE PHONE [H-8] or dial “0”):...

NEAX2400 IMX Hotel Feature Programming Manual
Page 106ND-70284 (E), Issue 2
D-23 Direct Page Connection
Assignment Procedure 
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
73b
0Type of Paging Service (only for calling)
b
1b0b1b0 
0 0 = No Answer 1 0 =Delay
0 1 = None Delay 1 1 =Delay with Paging Transfer b
1
b2
Radio Page Number
(NEAX2400 IMX, 1 IMG = 2 Digits only)
0/1 = 2 digits/3 digits
b
3Paging Cancel Code
0/1 = Individual Paging Route Codes/Common to all Paging Routes
b
4Radio Paging – station number...