NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 147
Guest Information Display – Hotel Attendant Console G-8
G - 8   G u e s t  I n f o r m a t i o n  D i s p l a y  –                                      
Hotel Attendant Console
General Description
This feature allows guest information to be displayed on a PMS terminal corresponding to the Console in the
following cases:
When the Console receives a call from a guest station
When the Console originates a call to a guest station...

NEAX2400 IMX Hotel Feature Programming Manual
Page 148ND-70284 (E), Issue 2
G-8 Guest Information Display – Hotel Attendant Console
Assignment Procedure
STEP CMND BIT EXPLANATION
CRT Control Even Group Queue (Note)
1SYS1
ASYD
INDEX 
190b
0
I/O = Port designation to Host Computer
b
1
b2
b3
Not used b4
b5
b6Transmission Protocol between PBX and Host Computer
b
7
CRT Control Odd Group Queue (Note)
2SYS1
ASYD
INDEX
191
(Note)b
0
I/O = Port designation to Host Computer
b
1
b2
b3
Not used b4
b5
b6Transmission...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 149
Guest Information Display – Hotel Attendant Console G-8
Note:
Assign INDEX 191 when five or more PMS terminals are used and Even/Odd is determined by the last digit of the
Console Number. 4AHSY
INDEX
110b
0
Room key Interface
0: Interface is absent (STAY/OUT is displayed)
1: Interface is present (Key status is displayed)
b
1Hotel – ATT Guest Information Service
0/1 = Not Required/Required
b
2Not used
b
3Called Number Display on...

NEAX2400 IMX Hotel Feature Programming Manual
Page 150ND-70284 (E), Issue 2
G-9 Guest Information Display – PMS Terminal
G-9 Guest Information Display – PMS Terminal
General Description
This feature allows guest information to be displayed on a Special Administration Station using a PMS port in the
following cases:
When a Special Administration Station receives a call from a Guest Station.
When a Special Administration Station originates a call to a Guest Station.
Operating Procedure
Call termination...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 151
Guest Information Display – PMS Terminal G-9
Assignment Procedure 
STEP CMND BIT EXPLANATION
CRT Control Even Group Queue (Note 1)
1SYS1
ASYD
INDEX 
190b
0
I/O = Port designation to Host Computer
b
1
b2
b3
Not used b4
b5
b6Transmission Protocol between PBX and Host Computer
b
7
CRT Control Odd Group Queue (Note 1)
2SYS1
ASYD
INDEX
191b
0
I/O = Port designation to Host Computer
b
1
b2
b3
Not used b4
b5
b6Transmission Protocol...

NEAX2400 IMX Hotel Feature Programming Manual
Page 152ND-70284 (E), Issue 2
G-9 Guest Information Display – PMS Terminal
Note 1:
Assign INDEX 191 when five or more PMS terminals are used.
Note 2:
Depending on the last digit of the Station Number, Even Group Queue or Odd Group Queue is determined if five or
more PMS terminals are used. 3AHSY
INDEX
110b
0
Room key Interface
0: Interface is absent (STAY/OUT is displayed)
1: Interface is present (Key status is displayed)
b
1Hotel – ATT Guest Information...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 153
Guest Room Calling – Hotel Attendant G-11
G-11 Guest Room Calling – Hotel Attendant
General Description
This feature allows the Console operator to display guest room information before calling a guest room.
Operating Procedure
Service Conditions
1. This feature is not effective when calling an Administration Station. When an Administration Station is
called, the station is rung immediately after the dialing is completed by the...

NEAX2400 IMX Hotel Feature Programming Manual
Page 154ND-70284 (E), Issue 2
G-11 Guest Room Calling – Hotel Attendant
Service Conditions (cont’d)
Figure 9  DSS Key/Station Correspondence and Lamp Indications
4. If DSS status display is not set in system data, the guest room rings immediately after being dialed.
5. When the slave room of the SUITE ROOM SERVICE [S-75] is called by the DSS key, TIMING START
[T-21] is not effective.
6. This feature is not available for remote guest stations when Centralized...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 155
Guest Room Calling – Hotel Attendant G-11
2SYS1
ASYD
INDEX 
78b
0Calling and Intermediate Station Number indication (Dterm and Console)
0/1 = Out/In Service (Always assign “1”.)
b
1Kind of Service Class indication (Dterm)
0/1 = Out/In Service (Always assign “1”.)
b
2Not used
b
3Station Number with Name Display
0/1 = Out/In Service
b
4Not used
b
5Name Display Service
0/1 = Out/In Service
b
6Not used
b
7
3SYS1
ASYD
INDEX 
161b...

NEAX2400 IMX Hotel Feature Programming Manual
Page 156ND-70284 (E), Issue 2
G-11 Guest Room Calling – Hotel Attendant
STEP CMND BIT EXPLANATION
5AHSY
INDEX
188b
0
Processing for Suite Room Station/Connecting Room Station Busy
b
1 b0
00= Busy Tone
0 1 = An idle station within the room is called
1 0 = The call is transferred to the Console if the caller is not the console operator. b
1
b2Fixed Data
b
3
b4Not used
b
5
When a call terminates to the Double Room Suite
0 = All stations ring simultaneously
1 =...