NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 107
Direct Page Connection D-23
5ARTDAssign the paging route data.
(OSGS = 2, ONSG = 1, TCL = 8, L/T = 1)
6 ATRK Assign the LENS data of the Paging trunk.
7 MBTK Make idle the assigned Paging trunk.
8ASATAssign the Individual Attendant Access number.
(The number is used as the paging answer code.)
9 ARSC Allow the connection between the station RSC and incoming trunk route. STEP CMND EXPLANATION 

NEAX2400 IMX Hotel Feature Programming Manual
Page 108ND-70284 (E), Issue 2
D-24 Direct Paging
D-24   Direct Paging
General Description
This feature eliminates the need for the Attendant to dial for paging access. While pressing the PG key on the
Console, the Attendant is directly connected to customer-provided paging equipment.
Operating Procedure
To establish connections to paging equipment, press the PG key on the console and page the desired party.
Service Conditions
1. Paging equipment is to be...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 109
Direct Service Set/Reset D-25
D-25   Direct Service Set/Reset
General Description
When the Attendant responds to guest calls via the GST or ANSWER key on the Console, or when a call is
answered at the Front Desk Terminal, DIRECT SERVICE is established by pressing the associated set/reset key.
Station number dialing, ENTER and EXIT operations are not required. DIRECT-SERVICE SET/RESET is
available for the following:
AUTOMATIC...

NEAX2400 IMX Hotel Feature Programming Manual
Page 110ND-70284 (E), Issue 2
D-25 Direct Service Set/Reset
Service Conditions (cont’d)
2. DIRECT SERVICE SET/RESET is available after a guest station calls the Attendant or the Front Desk
Terminal, and until the attendant presses the CANCL key. The guest station is not required to remain
connected for the service to be initiated.
Assignment Procedure
Refer to “Assignment Procedure” for DO NOT DISTURB [D-11], MESSAGE WAITING [M-6], AUTOMATIC
WAKE-UP [A-10],...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 111
Direct Station Selection D-26
D-26   Direct Station Selection
General Description
Ten DIRECT STATION SELECTION (DSS) keys are provided on the Console for direct access to frequently called
Administration or service stations such as restaurant, valet, maid, etc.
Operating Procedure
Press the loop and the desired DSS key to originate a call.
Service Conditions
1. A maximum of ten keys are provided for DIRECT STATION SELECTION on...

NEAX2400 IMX Hotel Feature Programming Manual
Page 112ND-70284 (E), Issue 2
D-88 Directory Assistance Interface
D-88   Directory Assistance Interface
General Description
This feature allows the Console operator to search for the station number of a guest via the PMS terminal. The
Console must have a PMS terminal dedicated to directory assistance. The guests name, station number, and other
information normally exchanged between the PMS and NEAX2400 IMX are entered into the PMS data base at
Check-In. The...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 113
Directory Assistance Interface D-88
Assignment Procedure
Note:
Assign INDEX 191 when five or more PMS terminals are used and Even/Odd is determined by the last digit of the
Console Number. STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
190b
0
I/O = Port designation to Host Computer
b
1
b2
b3
Not Used b4
b5
b6
Transmission Protocol between PBX and Host Computer
b
7
2SYS1
ASYD
INDEX
191
(Note)b
0I/O = Port designation to Host...

NEAX2400 IMX Hotel Feature Programming Manual
Page 114ND-70284 (E), Issue 2
D-89 Direct Selection – Outside
D-89   Direct Selection – Outside
General Description
Ten DIRECT STATION SELECTION (DSS) [D-26] keys are provided on the Console for direct access to
frequently called outside numbers or to emergency numbers such as fire, police, or ambulance.
Operating Procedure
To originate a call, press LOOP key and the desired DSS key.
Service Conditions
1. A maximum of ten keys are provided for DIRECT STATION...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 115
Dterm With Hotel Function D-105D
D-105D   Dterm With Hotel Function
General Description
This feature allows the users of 16-button or 24-button Dterm to control the following services by operating
programmable line/feature keys in the same manner as the keys of the Hotel Console. Fifteen programmable feature
keys are assigned to the Front Desk Terminal to provide full hospitality functionality.
AUTOMATIC WAKE-UP [A-10] Set/Reset...

NEAX2400 IMX Hotel Feature Programming Manual
Page 116ND-70284 (E), Issue 2
D-105D Dterm With Hotel Function
Operating Procedure (cont’d)
For AUTOMATIC WAKE-UP [A-10]
Idle Condition:
Connected to a guest station:
Step Action Result
1
Press the WUS or WUR key.The LCD shows the feature 
abbreviation.
2
Enter the WAKE-UP time in 24-hour time. (See 
AUTOMATIC WAKE-UP [A-10] for enhanced 12-hour time 
entry.)
3Enter the guest station number.
4Press the ENT key
5Press the END key.
6Press the CE key to clear...