NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 265
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 1
0-FFP (Firmware Processor) Number setting for the
DAID card.
By this setting, the system regards the DAID card
and the opposite DAIE card as one Firmware Pro-
cessor.
0 Not used
1FP No. 1
2FP No. 2
3FP No. 3
4-F Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 266ND-70928 (E), Issue 1.0
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel signaling data 
transmission speed: 64kbps
2ONCRC Synchronization Detection 
Timer is provided.
CRC Synchronization Detection 
Timer is not provided.
3ON CRC4 Check is provided.
CRC4 Check is not provided.
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 267
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 4, NOTE 5 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS 4
ON OFF ON ON ON TS 5
OFF OFF ON ON ON TS 6
ON ON OFF ON ON TS 7
OFF ON OFF ON ON TS 8
ON OFF OFF ON ON TS 9
OFF OFF OFF ON ON TS 10
ON ON ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 268ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 269
NOTE 3:
When clock source office signal is supplied via the line between the main site and the
remote site, set the SW1-1 and SW1-2 as the following table. In this case, DAID cards
(DAID0, DAID1) must be mounted in PIM0.
NOTE 4:
The time slot number 0 and 28 (TS0/28) cannot be used for control signal.
NOTE 5:
This setting must be identical with the opposite DAIE card....

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 270ND-70928 (E), Issue 1.0
PN-DAIE (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when a link between this card and a distant office is
normally connected.
Goes out after 15 seconds of link disconnection.
RMT Red Remains lit when receiving the alarm signal from a...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 271
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE 
(Rotary SW)
0-FAlways set to 0
1-F
Not used
MB (Toggle SW)
NOTE 1UP
For make-busy
For normal operation
SW1 
(Piano Key SW)1
Always set to OFF
2
Always set to OFF
3
Always set to OFF
4
Always set to OFF
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 272ND-70928 (E), Issue 1.0
SW2 (DIP SW)
4Setting of control signal time slot
NOTE 2, NOTE 3 OFF
5
OFF
6
OFF
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
23
45
67
8ON
ON
SWITCH NUMBER
TIME SLOT
NUMBER
45678
OFFONONONON TS 1
ON OFF ON ON ON TS 2
OFF OFF ON ON ON TS 3
ON ON OFF ON ON TS 4
OFF ON OFF ON ON TS 5
ON OFF OFF ON ON TS 6
OFF OFF OFF ON ON TS 7
ON ON ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIE (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 273
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
NOTE...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIF (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 274ND-70928 (E), Issue 1.0
PN-DAIF (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when the following connection are normal.
Control channel link between the DAID card and DAIE card.
Connection between the opposite DAIF card.
Goes out after 15 seconds of link...