NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC00 (CCH)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 305
Switch Settings
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW0
(Piano Key SW)1ON Loop-back test
For normal operation
2ON Analog interface
OFF Digital interface
3ONRS-232C RTS signal (to MODEM)...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC00 (CCH)
NEAX2000 IVS2 Installation Procedure ManualPage 306ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC01 (DCH)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 307
PN-SC01 (DCH)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LC Green Remains lit when communications are normally ongoing with the
D channel data links connected.
LPB Green Not used
SENSE
RUN
MB
SW0
LC 
LPB SW1 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC01 (DCH)
NEAX2000 IVS2 Installation Procedure ManualPage 308ND-70928 (E), Issue 1.0
Switch Settings
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW0
(Piano Key SW)1 Always set to OFF
2 Always set to OFF
3 Always set to OFF
4ON AP No. 04-15
OFF AP No. 20-31
(Continued)
F
4
AP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC01 (DCH)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 309
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC03 (ICH)
NEAX2000 IVS2 Installation Procedure ManualPage 310ND-70928 (E), Issue 1.0
PN-SC03 (ICH)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
DOPE7 Green Remains lit when No. 7 circuit D channel link is connected.
DOPE6 Green Remains lit when No. 6 circuit D channel link is connected.
DOPE5 Green Remains lit when No. 5 circuit D channel link is...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC03 (ICH)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 311
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC03-A (CSH)
NEAX2000 IVS2 Installation Procedure ManualPage 312ND-70928 (E), Issue 1.0
PN-SC03-A (CSH)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
DOPE7 Green Remains lit when No. 7 circuit D channel link is connected.
DOPE6 Green Remains lit when No. 6 circuit D channel link is connected.
DOPE5 Green Remains lit when No. 5 circuit D channel...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC03-A (CSH)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 313
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M537 (EXPMEM)
NEAX2000 IVS2 Installation Procedure ManualPage 314ND-70928 (E), Issue 1.0
PZ-M537 (EXPMEM)
Locations of Lamps, Switches, and Connectors
FA C E
REAR
CONNR: To CONN connector on 
PN-CP14 (MP) or
PN-AP00-B (AP00)
CONNR
SW