NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 295
Lamp Indications
Switch Settings
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LC Green Remains lit when communications are normally ongoing with the 
D channel data links connected.
LPB–Not used
CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC) 
errors.
PCM Red Remains lit when detecting PCM signal...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure ManualPage 296ND-70928 (E), Issue 1.0
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
SW0
(Piano Key SW)
1
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO 0 input on MP card.
OFFSource clock signal from network is 
not sent to the PLO 0 input on MP 
card. 
2 
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO 1 input on MP card.
OFFSource clock signal from...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 297
SW1
(Piano Key SW)
NOTE 41 Not used
2 Not used
3 Not used
4ON AP No. 04-15
OFF AP No. 20-31
SW2 (DIP SW) 1
Always set to OFF
2[North America only for AT&T]
ONDeletion of Area Code on 
International Outgoing call
OFFNo deletion of Area Code on 
International Outgoing call
[Australia/Other countries]
Always set to OFF
3 Always set to OFF
4 Always set to OFF
5 Always set...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure ManualPage 298ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 299
NOTE 3:
Set SW0-1 and SW0-2 as follows:
NOTE 4:
When the PBX is a clock source office, set the SW0-1 and SW0-2 on all the PRT cards
mounted in PIM0 to “OFF”.
NOTE 5:
Mount the PRT card which receives a source clock signal into PIM 0.
CONDITIONSPRT0 PRT1 PRT2 PRT3 PRT4
REMARKS
SW
0-1SW
0-2SW
0-1SW
0-2SW
0-1SW
0-2SW
0-1SW
0-2SW
0-1SW
0-2
When one PRT 
is provided.ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4RSTB (MFR)
NEAX2000 IVS2 Installation Procedure ManualPage 300ND-70928 (E), Issue 1.0
PN-4RSTB (MFR)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
OPE0-3 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
SENSE
RUN
MB...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4RSTB (MFR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 301
Switch Settings
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
SWITCH NAMESWITCH 
NUMBERSETTING
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to
be set by CM05
0-3 Not used
MB (Toggle SW)...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4RSTC (CIR)
NEAX2000 IVS2 Installation Procedure ManualPage 302ND-70928 (E), Issue 1.0
PN-4RSTC (CIR)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
BL0-3 Red Remains lit when receiving a CALLER ID (CLASS SM) signal.
SENSE
RUN
MB
BL3 
BL2 
BL1 
BL0 SW1
JP0 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-4RSTC (CIR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 303
Switch Settings
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to
be set by CM05.
0-3 Not used
MB (Toggle...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-SC00 (CCH)
NEAX2000 IVS2 Installation Procedure ManualPage 304ND-70928 (E), Issue 1.0
PN-SC00 (CCH)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LC Green Remains lit when communications are normally ongoing with the 
common signalling channel data links connected.
LPB Green Remains lit when a loop-back test is in progress.
RS
SENSE
RUN
MB
SW0
LC...