NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIA (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 255
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIA (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 256ND-70928 (E), Issue 1.0
NOTE 3:
When clock source office signal is supplied via the line between the main site and the
remote site, set the SW1-1 and SW1-2 as the following table. In this case, DAIA cards
(DAIA0, DAIA1) must be mounted in PIM0.
NOTE 4:
The time slot number 0, 20, 21, and 22 (TS0/20/21/22) cannot be used for control sig-
nal.
NOTE 5:
This setting must be identical with the...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIB (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 257
PN-DAIB (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when a link between this card and a distant office is
normally connected.
Goes out after 15 seconds of link disconnection.
RED Red Remains lit when detecting PCM signal loss or...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIB (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 258ND-70928 (E), Issue 1.0
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
0-FAlways set to 0
1-F Not used
MB (Toggle SW)
NOTE 1UP For make-busy
For normal operation
SW1
(Piano Key SW)1 Always set to OFF
2 Always set to OFF
3 Always set to OFF
4 Always set to OFF
(Continued)
0
ON
DOWN
4 
3 
2 
1 OFF
ON
OFF
OFF
OFF
OFF 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIB (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 259
SW2 (DIP SW)
1ONControl channel signaling data 
transmission speed: 48kbps
Control channel signaling data 
transmission speed: 64kbps
2ONDTI frame configuration: 12-Multi 
Fram e
DTI frame configuration: 24-Multi 
Fram e
3ON Line code: AMI with ZCS
Line code: B8ZS
4ONSetting of control signal time slot
NOTE 2, NOTE 3 5ON
6ON
7
OFF
8ON
(Continued)
SWITCH NAMESWITCH...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIB (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 260ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the circuit card.
NOTE...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIC (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 261
PN-DAIC (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when the following connection are normal.
Control channel link between the DAIA card and DAIB card.
Connection between the opposite DAIC card.
Goes out after 15 seconds of link...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIC (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 262ND-70928 (E), Issue 1.0
Switch Settings
SWITCHNAME SWITCH
NUMBER SETTING
POSITION FUNCTION CHECK
MB (Toggle SW) 
N
OTE UP For make-busy
For normal operation
SW1  
(Piano Key SW) 1 Always set to OFF 
2 Always set to OFF 
3 Always set to OFF 
4 Always set to OFF
SW2 (DIP SW) 1 Not used 
2ON
DTI frame configuration: 12-Multi  
Fram e 
DTI frame configuration: 24-Multi  
Fram e
3 ON Line code: AMI...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAIC (DAI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 263
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE:
When the power is on, flip MB switch to ON (UP position) before plugging/unplugging
the circuit card.  SW3 (DIP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-DAID (DAI)
NEAX2000 IVS2 Installation Procedure ManualPage 264ND-70928 (E), Issue 1.0
PN-DAID (DAI)
Location of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LINK Green Remains lit when a link between this card and a distant office is
normally connected.
Goes out after 15 seconds of link disconnection.
RMT Red Remains lit when receiving the alarm signal from a...