NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-30DTC-A (DTI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 285
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM when this card is normally operating.
PCM Red Remains lit when detecting PCM signal loss.
FRM Red Remains lit when detecting Frame Alignment signal loss.
MFRM Red Remains lit when detecting Multi-Frame Alignment signal loss on 
time Slot 16.
RMT Red Remains lit when receiving the alarm from a...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-30DTC-A (DTI)
NEAX2000 IVS2 Installation Procedure ManualPage 286ND-70928 (E), Issue 1.0
Switch Settings
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENS 
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2UP
For make-busy
For normal operation
(Continued)
F
4
AP No.SW-8: ON
04 05 06 07 08 09 10 11 12 13 14 15
SW-8: OFF
20 21 22 23 24 25 26 27 28 29 30 31
SW No.
456789ABCDEF...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-30DTC-A (DTI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 287
SW
(Piano Key SW)
1
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO 0 input on MP card.
OFFSource clock signal from network is 
not sent to the PLO 0 input on MP 
card 
2
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO 1 input on MP card.
OFFSource clock signal from network is 
not sent to the PLO 1 input on MP 
card. 
3ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-30DTC-A (DTI)
NEAX2000 IVS2 Installation Procedure ManualPage 288ND-70928 (E), Issue 1.0
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-30DTC-A (DTI)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 289
NOTE 3:
Set the SW-1 and SW-2 as follows:
NOTE 4:
When the PBX is a clock source office, set the SW-1 and SW-2 on all the DTI cards
mounted in PIM0 to “OFF”.
NOTE 5:
Mount the DTI card which receives a source clock signal into PIM0. CONDITIONSDTI0 DTI1 DTI2 DTI3
REMARKS
SW
-1SW
-2SW
-1SW
-2SW
-1SW
-2SW
-1SW
-2
When one DTI is 
provided.ON OFF––––––MP card will...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-IPTA (IPT)
NEAX2000 IVS2 Installation Procedure ManualPage 290ND-70928 (E), Issue 1.0
PN-IPTA (IPT)
Locations of Lamps, Switches, and Connectors
SW1
MODE
SW2VCT
IP 
CONN
VCT :
IP CONN :
TO EXTERNAL 
LAN INTERFACE SENSE
RUN
MB
BUSY 
SUBOPE3 
SUBOPE2 
SUBOPE1 
SUBOPE0 
L3 
L2 
L1 
IP-TX 
IP-RX 
IP-100M 
IP-LINK 
IP-COL 
IP-LYR 
 
PZ-M539
PN-IPTA
TO PN-4VCTH 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-IPTA (IPT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 291
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
BUSY Red When even 1-line ON: Even one line is busy
When even 1-line OFF: All lines are idle
SUBOPE3 Green Remains lit when Card No.3 of PN-4VCTH is operating.
SUBOPE2 Green Remains lit when Card No.2 of PN-4VCTH is operating.
SUBOPE1 Green Remains lit when Card...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-IPTA (IPT)
NEAX2000 IVS2 Installation Procedure ManualPage 292ND-70928 (E), Issue 1.0
Switch Settings
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENSE
(Rotary SW)
NOTE 10-3 Not used
4-F Set the switch to match the AP Number (04-31) to
be set by CM05.
MB (Toggle SW)
NOTE 2UP For make-busy
For normal operation
MODE 
(Rotary SW)
0For setting of the operating mode
For normal operation
1-F Not used
(Continued)
F
4
AP No.SW1-4: ON
04 05 06 07 08 09...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-IPTA (IPT)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 293
The figure in the SWITCH NAME column and the position in   the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB switch to ON (UP...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-24PRTA (PRT)
NEAX2000 IVS2 Installation Procedure ManualPage 294ND-70928 (E), Issue 1.0
PN-24PRTA (PRT)
Locations of Lamps, Switches, and Connectors
SENSE
RUN
MB
SW2
LC 
LPB 
CRC 
PCM 
FRM 
RMT 
AIS 
BL 
   
 
 
 
 
 
  SW1
SW0
JRR1
AISS MAS
JPR0
JPS