NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M537 (EXPMEM)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 315
Lamps Indications
This card has no lamps.
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M537 (EXPMEM)
NEAX2000 IVS2 Installation Procedure ManualPage 316ND-70928 (E), Issue 1.0
Mounting PZ-M537 Card
When mounting the EXPMEM card on the AP00/MP card, do the following procedure.
STEP 1: Take off three screws from the rear side of EXPMEM suppor t.
NOTE:
Supports and screws are attached to the EXPMEM card.
STEP  2: Connect the CONNR connector on the EXPMEM card and the CONN connector on the
AP00/MP card.
STEP 3: Secure the EXPMEM card to the...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M542 (CONN)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 317
PZ-M542 (CONN)
Locations of Lamps, Switches, and Connectors
Lamp Indications
This card has no lamps.
JP2
RCV21
FOR 
No.2 
CIRCUIT 
 
LT CJP1LTTO LTC CONNECTOR 
ON BWB IN PIM TO CHAMP 
CONNECTOR (MDF)
JP0
TRS21
TRS01
FOR 
No.0 
CIRCUIT
COAXIAL CONNECTORRCV01
RCV11
FOR 
No.1 
CIRCUITTRS11 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M542 (CONN)
NEAX2000 IVS2 Installation Procedure ManualPage 318ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
JP0 For coaxial connectors
(No. 0 circuit)...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M557 (CONN)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 319
PZ-M557 (CONN)
Locations of Lamps, Switches, and Connectors
Lamp Indications
This card has no lamps.
JP2
RCV20
FOR 
No.2 
CIRCUIT 
 
LT CJP1LTTO LTC CONNECTOR 
ON BWB IN PIM TO CHAMP 
CONNECTOR (MDF)
JP0
TRS20
TRS00
FOR 
No.0 
CIRCUIT
COAXIAL CONNECTORRCV00RCV10
FOR 
No.1 
CIRCUIT
TRS10 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-M557 (CONN)
NEAX2000 IVS2 Installation Procedure ManualPage 320ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
JP0 For coaxial connectors
(No. 0 circuit)...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 321
LINE/TRUNK CARD
The table below shows the line/trunk cards to be explained in this section.
Table 3-3  List of Line/Trunk Cards 
NAME
(FUNCTIONAL
NAME)LAMP
X: PROVIDED
–:NOT 
PROVIDEDSWITCH
X: PROVIDED
–:NOT 
PROVIDEDEXTRACTION/
INSERTION WITH 
POWER ON
X: ALLOWED
: ALLOWED 
AFTER MB*
–: NOT ALLOWEDREFERENCE
PA G E
PN-2AMPA (AMP) X–XPage 324
PN-AUCA (AUC) X–XPage 325...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure ManualPage 322ND-70928 (E), Issue 1.0
PN-2DITA (DIT)
X–XPage 346
PN-4DITB (DIT)
X–XPage 347
PN-DK00 (DK)
––XPage 348
PN-2DLCB/2DLCN
(DLC)X–XPage 349
PN-2DLCC (DLC)
X–XPage 350
PN-4DLCF (DLC) 
X–XPage 351
PN-4DLCM (DLC) 
X–XPage 352
PN-4DLCQ (DLC) 
X–XPage 353
PN-8DLCL (DLC) 
X–XPage 354
PN-8DLCP (DLC) 
X–XPage 355
PN-2DPCB (DPC)
XX XPage 356
PN-2ILCA (ILC)
XX XPage 360
PN-4LCC (LC)
X–XPage 363
PN-4LCD-A...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
Line/Trunk Card
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 323
PN-2LDTA (LDT)
X–XPage 372
PN-M03 (M03)
XX XPage 373
PN-M10 (M10)
XXPage 376
PN-2ODTA (ODT)
X–XPage 378
PN-2ODTB (ODT)
X–XPage 379
PN-8RSTA (PBR)
––XPage 380
PN-TNTA (TNT)
–XXPage 381
PN-4VCTH (VCT)
XX XPage 383
PZ-8PFTB (PFT)
––XPage 385
PZ-VM00-M (VM)
XXPage 386
PN-VM01 (VM)
XX–Page 389
*MB = Make Busy
Table 3-3  List of Line/Trunk Cards (Continued)
NAME...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-2AMPA (AMP)
NEAX2000 IVS2 Installation Procedure ManualPage 324ND-70928 (E), Issue 1.0
PN-2AMPA (AMP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
Switch Settings
This card has no switches.
LAMP 
NAMECOLOR FUNCTION
BL0, 1 RedRemains lit when the corresponding circuit is in use.
Flashes at 60 IPM when the corresponding circuit is in make-
busy state or the system data for this card is not assigned.
BL1
BL0