NEC Neax 2000 Ivs2 Installation Procedure Manual

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CP15 (FP)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 215
PN-CP15 (FP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
SENSE
RUN
MB
SW1 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-CP15 (FP)
NEAX2000 IVS2 Installation Procedure ManualPage 216ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and    , the setting of the switch varies with the system concerned.
NOTE 1:
Set the groove on the switch to the desired position.
NOTE 2:
When the power is on, flip the MB...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-PW00 (EXTPWR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 217
PN-PW00 (EXTPWR)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Remains lit while –48V power is being supplied
RUN
MB08
07
06
05-48V
-48V
E
E
04
03
02
01-48V
-48V
E
E
CONNTO DESKCON 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PN-PW00 (EXTPWR)
NEAX2000 IVS2 Installation Procedure ManualPage 218ND-70928 (E), Issue 1.0
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE:
When the power is on, flip the MB switch to ON (UP position) before plugging/unplug-
ging the...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-PW121 (AC/DC PWR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 219
PZ-PW121 (AC/DC PWR)
Locations of Lamps, Switches, and Connectors
SW 1
SW2 SW 102SW 301
SW 101
ON
OFF
BATT BATT
SW2
CN1 CN104 CN103 (SIGNAL)
MJ 
MN 
ON 
 MJ 
MN 
ON 
  

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-PW121 (AC/DC PWR)
NEAX2000 IVS2 Installation Procedure ManualPage 220ND-70928 (E), Issue 1.0
Lamp Indications 
Switch Settings
LAMP 
NAME COLOR FUNCTION
MJ Red Remains lit when a major trouble occurres or resident system
program is not properly loaded
MN Yellow Remains lit when a minor trouble occurres or resident system program is successfully loaded, or a station line is locked out
ON Green Remains lit while the operating power is being supplied
C...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-PW121 (AC/DC PWR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 221
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and    , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW301 (DIP SW)
1ON CR Voltage: 75Vrms
OFF CR Voltage:...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-PW122 (DC/DC PWR)
NEAX2000 IVS2 Installation Procedure ManualPage 222ND-70928 (E), Issue 1.0
PZ-PW122 (DC/DC PWR)
Locations of Lamps, Switches, and Connectors
SWON CONN
CONN connector: 
To PWR1 connector on PIM BWB
POWER OUTPUT CABLE (-48V, E): 
To PWR0C connector on PIM BWB 

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
PZ-PW122 (DC/DC PWR)
NEAX2000 IVS2 Installation Procedure Manual
ND-70928 (E), Issue 1.0Page 223
Lamp Indications 
Switch Settings
LAMP 
NAME COLOR FUNCTION
ON Green Remains lit while the operating power is being supplied
C
AU TIO N
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit
card into/from its mounting slot.
SWITCH NAME SWITCH
NUMBER SETTING
POSITION FUNCTION CHECK
SW
ON For turning AC power on
OFF For...

CHAPTER 3 LAMP INDICATIONS AND SWITCH SETTINGS
Application Processor Card
NEAX2000 IVS2 Installation Procedure ManualPage 224ND-70928 (E), Issue 1.0
APPLICATION PROCESSOR CARD
The table below shows the application cards to be explained in this section.
Table 3-2  List of Application Processor Cards 
NAME
(FUNCTIONAL
NAME)LAMP
X: PROVIDED
–:NOT 
PROVIDEDSWITCH
X: PROVIDED
–:NOT 
PROVIDEDEXTRACTION/
INSERTION WITH 
POWER ON
X: ALLOWED
: ALLOWED 
AFTER MB*
–: NOT ALLOWEDREFERENCE
PA G E
PN-AP00-A (DBM) X...