NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 228  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Paging Access-CCIS
Hardware Requirements
Paging trunk (PN-4COT) × n/4 (n: Number of external paging zones)
DK card
Paging equipment provided locally. 
For cross connection of the Paging Equipment, refer to the Installation Procedure Manual.
Operating Procedure
To access paging equipment through CCIS:
(1) Lift the handset; receive dial tone.
(2) Dial the paging feature access code.
(3) Connection to paging...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Restriction From Outgoing Calls-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 229
RESTRICTION FROM OUTGOING CALLS-CCIS
General Description
This feature automatically restricts users of preselected stations from placing outgoing calls and/
or certain miscellaneous trunk calls through CCIS without Attendant assistance.
Programming
Refer to Deluxe Traveling Class Mark-CCIS on Page 188.
Operating Procedure
No manual operation is required. 

 NEAX2000 IVS2 CCIS System ManualPage 230  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Single-Digit Station Calling-CCIS
SINGLE-DIGIT STATION CALLING-CCIS
General Description
This feature allows the assignment of single digit station numbers.
Programming
DIAL XSATELLITE OFFICE MAIN OFFICE
PBX IMX/PBXNo. 7 CCIS STATION NO. X 

CHAPTER 3 SYSTEM DATA PROGRAMMING
Single-Digit Station Calling-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 231
For Satellite Office
Operating Procedure
To operate:
(1) Lift the handset; receive dial tone.
(2) Dial the single-digit preprogrammed station number.
(3) The called station will be rung.
DESCRIPTION DATA
Assign the single-digit station number to 
LCR Group 3 (A129).
(1)
(2)Y=0-3 Number Plan Group 0-3
X: Access Code
A129: LCR Group 3
Assign an area code table to be...

 NEAX2000 IVS2 CCIS System ManualPage 232  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Station-to-Station Calling-CCIS
STATION-TO-STATION CALLING-CCIS
General Description
This feature permits any station user to dial another station directly through CCIS without
operator assistance.
Programming
In addition to the programming of flexible station numbering, perform the following programming:
Operating Procedure
To place a station-to-station call:
(1) Lift the handset and receive dial tone....

CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 233
TOLL RESTRICTION-3/6 DIGITS-CCIS
General Description
This feature allows the PBX to be programmed to restrict outgoing calls through CCIS according
to specific areas and/or Central Office codes. This restriction is determined on the basis of a
three-digit Area Code or six-digit area and Office Code numbering plan.
Programming
DESCRIPTION DATA
Provide the system with...

 NEAX2000 IVS2 CCIS System ManualPage 234  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
DESCRIPTION DATA
Provide the Toll Restriction feature to the 
required trunk routes.
(1)
(2)YY=11
00-63: Trunk Route No.
0: To provide
Specify the route access capability for 
each restriction class.
(1)
(2)YY=51-55
00-63: Trunk Route No.
0: Restricted
1 : Allow
Assign the Area Code Development 
Pattern number for Toll Restriction 
Analysis and Maximum Digit Analysis to...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 235
DESCRIPTION DATA
Specify the maximum number of digits 
dialed by the calling party. The maximum 
number of digits including the area codes 
should be assigned to each area code.
(1)
(2)Y=0-4 
Area Code Development Pattern No. 0-
4 assigned by CM8A Y=A000
X-X...X: Area Code dialed 
(Max. 8 digits)
01-24 : 1-24 digits
25-79 : 25-79 digits
Assign the area code to be...

 NEAX2000 IVS2 CCIS System ManualPage 236  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
DESCRIPTION DATA
To add the Tenant Pattern:
STEP 1 Assign the area code to be 
restricted and a Tenant Pattern 
number to the Area Code 
Development Pattern number 
assigned by CM35 YY=76.
STEP 2  Assign a Tenant number and a 
Route Pattern number to the 
Tenant Pattern number 
assigned by Step 1.
STEP 3  Assign a TR Pattern number to 
the Route Pattern number 
assigned by...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Toll Restriction-3/6 Digits-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 237
Operating Procedure
No manual operation is required.
DESCRIPTION DATA
STEP 3  Assign the starting time for the 
Toll Restriction and Route 
Pattern number to the Time 
Pattern number assigned by 
Step 2. Set the Starting Time as 
shown below.
Example:To set the 7:00 AM to 9:00 PM 
for the Toll Restriction, enter the 
following starting times one by 
one.
0700 (7:00...