NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 188  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Deluxe Traveling Class Mark-CCIS
DELUXE TRAVELING CLASS MARK-CCIS
General Description
This feature provides outgoing call restrictions within the CCIS network.
The following three types of restrictions are allowed:
Deluxe Traveling Class Mark Restriction
Route Restriction
Numbering Restriction.
Programming
DESCRIPTION DATA
Assign a Trunk Restriction Class to the 
required stations.
(1)
(2)YY=01 Trunk...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Deluxe Traveling Class Mark-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 189
DESCRIPTION DATA
Specify to outgoing/incoming call 
capability on each Route Restriction Class 
(RCA-RCH) assigned by CM12 YY=01 to 
each route.
NOTE:For the route assigned as C.O. 
line by CM35 YY=56 (RCF), 57 
(RCG), 58 (RCH) are 
automatically assigned to 
“Restricted”.















(1)
(2)YY=51 (RCA)
YY=52 (RCB)
YY=53 (RCC)
YY=54 (RCD)
YY=55...

 NEAX2000 IVS2 CCIS System ManualPage 190  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Deluxe Traveling Class Mark-CCIS
When changing the initial setting (see NOTE), or when receiving the IMX Trunk Restriction Class
(9-15) as a Deluxe Traveling Class Mark, execute the following programming.
DESCRIPTION DATA
Assign the IMX Trunk Restriction Class to 
each PBX Trunk Restriction Class for the 
restriction class conversion from the PBX 
to the IMX, if required.(1)
(2)20: TRK Restriction Class 1...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Deluxe Traveling Class Mark-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 191
NOTE:If no data is set, the default setting is shown below.
(1) PBX to IMX:
(2) IMX to PBX:
Operating Procedure
None (However, this feature is dependent on System Programming.)
1S T DATA 2ND DATA
20: TRK Restriction Class 1 (RCA)
21: TRK Restriction Class 2 (RCB)
22: TRK Restriction Class 3 (RCC)
23: TRK Restriction Class 4 (RCD)
24: TRK Restriction Class 5 (RCE)
25:...

 NEAX2000 IVS2 CCIS System ManualPage 192  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Dial Access To Attendant-CCIS
DIAL ACCESS TO ATTENDANT-CCIS
General Description
This feature allows a station user to call an Attendant Console by dialing an operator call code
through the CCIS network.
Programming
DESCRIPTION DATA
Specify the tenants to be handled by each 
ATTCON Group.
NOTE:When marking a link with the 
IMX Tenant number should be 
assigned as 01-63, not 00.
(1)
(2)Y=0-3: ATTCON Group...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Dial Access To Attendant-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 193
Operating Procedure
To call an Attendant Console:
(1) The station user dials the operator call code, then receives ringback tone.
(2) The ATND lamp for Incoming Call Identification flashes on the Attendant Console. The 
Attendant answers the call. 

 NEAX2000 IVS2 CCIS System ManualPage 194  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Direct-In Termination-CCIS
DIRECT-IN TERMINATION-CCIS
General Description
This feature automatically routes incoming exchange calls through CCIS to a predesignated
station in the network without Attendant assistance.
Programming
When a release signal arrives on the incoming (IC) trunk
DESCRIPTION DATA
Assign the data for terminating system in 
Day Mode, Night Mode, Mode A and Mode 
B of the trunk,...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Direct-In Termination-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 195
DESCRIPTION DATA
Specify the combination of trunk routes al-
lowing the Tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63 (Incoming Trunk Route)
ZZ: 00-63 (Outgoing Trunk Route for 
CCIS)
0: Allow
Assign the System Speed Dialing memory 
area used exclusively for DIT-Outside.(1)
(2)66: Exclusively for DIT-Outside
XXX YYY
XXX: 000-299 (First Memory/Slot No. 
in Block)
YYY:...

 NEAX2000 IVS2 CCIS System ManualPage 196  ND-70918 (E), Issue 1.0
CHAPTER 3 SYSTEM DATA PROGRAMMING
Direct-In Termination-CCIS
When no release signal arrives on the IC trunk.
DESCRIPTION DATA
Provide the DIT-Outside feature. (In case 
of no release signal on IC trunk.)(1)
(2)324: DIT-Outside
0: Allow
(When both answer and release signal 
appear on the OG trunk)
Assign the data for terminating system in 
Day Mode, Night Mode, Mode A and Mode 
B for the trunk, respectively.



(1)
(2)YY=02 Day Mode...

CHAPTER 3 SYSTEM DATA PROGRAMMING
Direct-In Termination-CCIS
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 197
Operating Procedure
The outside calling party dials the telephone number as usual. The call is answered at a
predesignated station within the CCIS network, bypassing the Attendant Console.
DESCRIPTION DATA
Assign Trunk Route data to the trunk route 
number (for OG route).
(1)
(2)YY=04 
Answer Signal from Distant Office
00-63: Trunk Route No.
2: Arrive

(1)
(2)YY=05...