NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 268  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP15 (FP)
PN-CP15 (FP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while the circuit card is operating normally.
SENSE
RUN
MB
SW1 

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP15 (FP)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 269
Switch Settings
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and    , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON...

 NEAX2000 IVS2 CCIS System ManualPage 270  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
PN-AP00-B (AP00)
Locations of Lamps, Switches, and Connectors
CONN: To CONNR connector on PZ-M537 (EXPMEM)
RS3
RS2
RS1
RS0
SENSE
RUN
MB
SW0 SW2
L3 
L2 
L1 
L0 SW1 CONN
JP0
JP1 

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 271
Lamp Indications
Switch Settings
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
L0-L3 Green Second data setting value for CMD001 > 250
0 1 (Por t 0)-3 (Por t 2)
L3 Indication of transmitting 
status of Port 0Indication of CTS signal status on 
Po r t  0 - 2
L2 Indication of transmitting 
status of Port 1Indication of DCD signal status...

 NEAX2000 IVS2 CCIS System ManualPage 272  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
SW0 (Dip SW) 1-3
ONNot used
For normal operation
4, 5 For normal operation
OFFNot used
6
NOTE 3ONSets No. 0 Port forcibly in a state 
which DSR signal is always provided.
OFFReceives DSR signal from the DCE 
on No. 0 Port.
7
NOTE 3ONSets No. 1 Port forcibly in a state 
which DSR signal is always provided.
OFFReceives DSR signal from the DCE 
on No. 1 Port.
8
NOTE 3ONSets No. 2 Port...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 273
SW2 (Dip SW)
1
NOTE 3ONSets No. 3 Port forcibly in a state 
which DSR signal is always provided.
OFFReceives DSR signal from the DCE 
on No. 3 Port.
2ONEnables the receive clock from the 
DCE (Modem) when No. 1 Port is 
synchronous. (Clock is received at 
the RXC terminal)
OFFUses internal clock as the receive 
clock when No. 1 Port is 
synchronous.
When No. 1 Port is...

 NEAX2000 IVS2 CCIS System ManualPage 274  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position) before...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-AP00-B (AP00)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 275
NOTE 4:The use of the external clock (from the distant end) or the internal clock is determined
by the following table:
CLOCKSW2
26
External ON OFF
Internal OFF ON 

 NEAX2000 IVS2 CCIS System ManualPage 276  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PN-24DTA-C (DTI)
PN-24DTA-C (DTI)
Locations of Lamps, Switches and Connectors
SENSE
RUN
MB
 
 
CRC 
PCM 
FRM 
RMT 
AIS 
BL 
   
 
 
 
 
 
  SW1
SW0
JRR1
AISS MAS
JPR0
JPS 

CHAPTER 4 CIRCUIT CARD INFORMATION
PN-24DTA-C (DTI)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 277
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC) 
errors.
PCM Red Remains lit when detecting PCM signal loss.
FRM Red Remains lit when detecting Frame Alignment signal loss.
RMT Red Remains lit when receiving Frame Alignment signal loss alarm 
from a...