NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 288  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PN-SC00 (CCH)
PN-SC00 (CCH)
Locations of Lamps, Switches and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
LC Green Remains lit when communications are normally ongoing with the 
common signalling channel data links connected.
LPB Green Remains lit when a loop-back test is in progress.
RS
SENS
RUN
MB
SW0
LC
LPB SW1
TO  M O D EM...

CHAPTER 4 CIRCUIT CARD INFORMATION
PN-SC00 (CCH)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 289
Switch Settings
SWITCH
NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SENS
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-31) to 
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2
UP For make-busy
For normal operation
SW0
(Piano Key SW)
1ON Loop-back test
For normal operation
2ON Analog interface
OFF Digital interface
3ONRS-232C RTS signal (to MODEM) 
ON  NOTE 3...

 NEAX2000 IVS2 CCIS System ManualPage 290  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PN-SC00 (CCH)
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position) before...

CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M537 (EXPMEM)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 291
PZ-M537 (EXPMEM)
Locations of Lamps, Switches and Connectors
FA C E
REAR
CONNR:  To CONN connector on PN-
CP14 (MP) or
PN-AP00-B (AP00)
SW
CONNR 

 NEAX2000 IVS2 CCIS System ManualPage 292  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M537 (EXPMEM)
Lamps Indications
This card has no lamps.
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
SW (Dip SW)
1For normal...

CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M537 (EXPMEM)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 293
Mounting PZ-M537 Card
When mounting the EXPMEM card on the AP00/MP card, do the following procedure.
STEP 1: Remove three screws from the rear side of EXPMEM support.
NOTE:Supports and screws are attached to the EXPMEM card.
STEP 2: Connect the CONNR connector on the EXPMEM card and the CONN connector on
the AP00/MP card.
STEP 3: Secure the EXPMEM card to the AP00/MP card with the...

 NEAX2000 IVS2 CCIS System ManualPage 294  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M542 (CONN)
PZ-M542 (CONN)
Locations of Lamps, Switches and Connectors
Lamp Indications
This card has no lamps.
JP2
RCV21
FOR 
No.2 
CIRCUIT 
 
LT CJP1LTTO LTC CONNECTOR 
ON BWB IN PIM TO CHAMP 
CONNECTOR (MDF)
JP0
TRS21
TRS01
FOR 
No.0 
CIRCUIT
COAXIAL CONNECTOR
RCV01RCV11
FOR 
No.1 
CIRCUIT
TRS11 

CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M542 (CONN)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 295
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
JP0For coaxial connectors
(No.0 circuit)
LEFTFor champ...

 NEAX2000 IVS2 CCIS System ManualPage 296  ND-70918 (E), Issue 1.0
CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M557 (CONN)
PZ-M557 (CONN)
Locations of Lamps, Switches and Connectors
Lamp Indications
This card has no lamps.
JP2
RCV20
FOR 
No.2 
CIRCUIT 
 
LT CJP1LTTO LTC CONNECTOR 
ON BWB IN PIM TO CHAMP 
CONNECTOR (MDF)
JP0
TRS20
TRS00
FOR 
No.0 
CIRCUIT
COAXIAL CONNECTOR
RCV00RCV10
FOR 
No.1 
CIRCUIT
TRS10 

CHAPTER 4 CIRCUIT CARD INFORMATION
PZ-M557 (CONN)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 297
Switch Settings
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH
NUMBERSETTING
POSITIONFUNCTION CHECK
JP0For coaxial connectors
(No.0 circuit)
LEFTFor champ...