NEC Neax 2000 Ivs2 Ccis System Manual

 NEAX2000 IVS2 CCIS System ManualPage 258  ND-70918 (E), Issue 1.0
This page is for your notes. 

NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 259
CHAPTER 4
CIRCUIT CARD 
INFORMATION
This chapter explains the mounting location, the meaning of lamp
indications, and the method of switch settings of each circuit card for
the No. 7 CCIS system. 

 NEAX2000 IVS2 CCIS System ManualPage 260  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
How to Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains each circuit card used in this system about the following items.
Explanations are given in alphabetical order of the circuit card names within each circuit card
category (Control, Application Processor, and Line/Trunk).
(1) Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors of each circuit...

CHAPTER 4  CIRCUIT CARD INFORMATION
Mounting Location of Circuit Card
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 261
MOUNTING LOCATION OF CIRCUIT CARD
This section explains the location for mounting circuit cards for the CCIS system.
Circuit Card Mounting Slots
Figure 4-1 shows circuit card mounting slots allocated in the PIM.
Figure 4-1  Mounting Location
*1PN-CP14 (MP) card on PIM0. PN-CP15 (FP) card on the FP11 slot on PIM0, and FP12 slot
on PIM 2, 4, 6. PZ-M537 (EXPMEM) card...

 NEAX2000 IVS2 CCIS System ManualPage 262  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
List of Required Cards
LIST OF REQUIRED CARDS
Table 4-1 shows the required cards to be explained in this section.
*MB = Make Busy
Table 4-1  List of Required Cards
NAME
(FUNCTIONAL
NAME)LAMP
X: PROVIDED
–: NOT 
PROVIDEDSWITCH
X: PROVIDED
–: NOT 
PROVIDEDEXTRACTION/
INSERTION WITH 
POWER ON
X:ALLOWED
:ALLOWED 
AFTER MB*
–: NOT ALLOWEDREFERENCE
PAGE
PN-CP14 (MP) X X–Page 263
PN-CP15 (FP) X XPage 268...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 263
PN-CP14 (MP)
Locations of Lamps, Switches, and Connectors
CONN: To CONNR connector on PZ-M537 (EXPMEM)
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally.
CLK Green Remains lit while receiving clock signals to the PLO.
SW3
RUN
SW1
SW2
CLK
VR
DK JACK CONNSW4
JP0JP1
RS1
RS0 

 NEAX2000 IVS2 CCIS System ManualPage 264  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
Switch Settings
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:Only when executing “MP Program Download” in MATWorX Studio, set the SW3 to 5-
8.
CAUTION
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit 
card into/from its mounting slot.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW3 (Rotary SW)
NOTE 1
0-FOn...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 265
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW1 (Push SW)For initializing CPU
SW2
(Piano Key SW)1ON A-law (Australia)
OFF µ-law (North America)
2, 3Selection of PLO0 input
(Phase Locked Oscillator)
For clock receiver office:
For clock source office:
SW2-2
SW2-3
OFF OFF
4ONWhen using RS1 port for built-in 
MODEM
OFF When using RS1 port for RS-232C
(Continued)
4 
3 
2 
1...

 NEAX2000 IVS2 CCIS System ManualPage 266  ND-70918 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW4 (Dip SW)
1Not used
2 Not used
3, 4Selection of PLO1 input
(Phase Locked Oscillator)
For clock receiver office:
For clock source office:
SW4-3
SW4-4
OFF OFF
VR (Rotary SW)
Variable Resister for External Hold 
Tone Source
(0 - 20 Kohms : Clockwise)
DK (Connector)
02 Ground detection
01 Ground sending
(Continued)
1
23
4ON
OFF
OFF...

CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 CCIS System Manual    
ND-70918 (E), Issue 1.0   Page 267
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
JP0 (Jumper pin)
UPNot used
(Memory backup OFF)
For normal operation
(Memory...