Mitel Sx 50 Dpabx Instructions Guide

Customer Data Entry Forms 
COMMAND 100 - SYSTEM OPTIONS PROGRAMMING 
- Register 16 PRINTER CONTROL 
- Data Demultiplexer Enable (0 = Disable, 1 = Enable) 
- Printer Baud Rate 
0 = 110 5 = 1800 
1=150 6 = 2400 
2 = 300 7=4800 
3 = 600 8 = 9600 
4 = 1200 
- Printer Parity 
0 = None 
1 =Odd 
2 = Even 
Number of TX Bits 
Number of Stop Bits 
Slow Carriage Return Option 
1 = Output Six Nulls at End-of-Line 
r Register 17 CONTACT MONITOR 
Contact Monitor Night Answer Point 
(During Attendant Inhibit or Night...

Features Description 
Automatic Ringdown Circuit 
Description This feature allows an extension designated as a Ringdown Circuit to be 
programmed into one of 10 circuit groups. When an Automatic Ringdown 
Circuit extension goes off-hook, the SXSO system automatically dials a 
preprogrammed number (internal or external). There are three types of 
Automatic Ringdown Circuit groups, as follows: 
l Automatic Ringdown Circuit Group 0 signals the attendant. This 
group acts 
as a Housephone. See MANUAL LINEin...

Features Description 
Automatic Route Selection and Toll Control 
Description 
Automatic Route Selection controls the routing and connection of a call 
based on the number dialed, the time of day, route availability, cost and 
the user’s toll restriction. Toll Control denies an extension the ability to 
make certain calls. The system activates denials on the receipt of the toll 
supervision, and on the actual digits dialed. For details, refer to Section 
910&091-220-NA, Automatic Route Selection and Toll...

Features Descriction 
Hotline 
Description 
This feature allows an extension designated as an Automatic Ringdown 
Circuit to be programmed into one.of 10 Hotline groups. When a Hotline 
extension goes off-hook, the SX40 system automatically dials a prepro- 
grammed number (internal or external). 
Hotline Groups 2 - 9 signal the destination programmed in Abbreviated Dial 
numbers 12 - 19 (102 --, 109), respectively. 
See AUTOMATIC RINGDOWN CIRCUIT in this Section for more 
information. 
1 Conditions 
l Do...

Features Description 
Hunt Groups - 
Description This feature defines a group of extensions as a Hunt Group and assigns 
them a Hunt Group Access Code. A call to a Hunt Group connects to the 
first idle extension in the group. There can be a maximum of six Hunt 
Groups of eight extensions defined: each with a unique access code. Al- 
ternatively, Hunt Groups can be linked to form larger Hunt Groups for a 
maximum configuration of one group of 48 extensions. Two types of hunt- 
ing are provided: Circular...

Features Description 
. 
. 
. 
DND activated, internal calls receive Do Not Disturb tone. Trunk calls 
go to LDNl . 
The last member to log out of a hunt group receives a short warning 
tone. On a 
SUPERSEl4 or SUPERSET telephone the LCD 
shows “LAST MEMBER”; followed by “HUNT GRP LOGOUT”. 
If all members are logged out, internal calls to the Hunt Group receive 
reorder tone. Trunk calls go to LDNl . 
A trunk programmed as a Direct+ Line to a Hunt Group will ring the 
Attendant on LDNl if all members are...

Features Description 
105 3-126 
- l If an extension dials a Hunt Group Access Code in which all exten- 
sions are busy, busy tone is returned. 
. If the attendant or an extension transfers a trunk call to a Hunt Group 
in which ail extensions are busy, the trunk. call camps on to the Hunt 
Group. The caller hears silence~or (if provided), Music on Hold. 
Login Hunt Groups 
To Log In: 
l Lift Handset. Dial tone is returned. (This step not required at. 
SUPERSET telephones). 
l Dial the Hunt Group...

Features Description 
Hunt Group Rerouting 
Description 
Conditions 
Programming Command 121-l 29, Class of Service Options, Register 6: 
Operation 
This feature, when enabled, allows an call incoming which is transferred 
to a hunt group and is not answered within the programmed 
time, to be 
rerouted to a preprogrammed destination. 
The System Timed Recall No Answer timer will determine, the reroute 
time. 
A destination must be preprogrammed in the corresponding 
Abbreviated Dial number if hunt group...

. 
.  

, Features 
Manual Line 
Description 
This feature allows an extension designated as an Automatic Ringdown 
Circuit to be programmed as a Manual tine. When a Manual Line 
extension goes off-hook, the SX-50 system automatically dials the 
Attendant. 
A manual line is typically used as a security phone or lobby phone. Dial tone 
is not provided. The extension receives calls normally. 
See AUTOMATIC RINGDOWN CIRCUIT in this Section for more 
information. 
R Conditions 
l Do not program port # 1 as a Manual...