Mitel Sx 50 Dpabx Instructions Guide

Documentation Index 
(I) 9104-091-301-NA, Remote Maintenance and Administration Test System 
(RMATS), describes RMATS Module installation, system programming and 
RMATS operation. 
(m) 9104-091-350-NA, Troubleshooting Procedures and General Maintenance In- 
formation, describes the maintenance philosophy, features and facilities of the 
SX-50 system. This Section also includes the troubleshooting procedures if a 
problem occurs with the operation after installation and/or programming. 
Table l-l...

Issue 3 
March, 1993 
SX-50@ DIGITAL PRIVATE 
AUTOMATIC BRANCH EXCHANGE 
(DPABX) 
Customer 
Data Entry 
Forms 
W, @ - Trademark of Yltel Corporation. 
@ Copyright 1993. Mltsl Corporation. 
All rights reserved. 
Printed in Canada. 
@ 
MITEL?  

Customer Data Entry Forms 
1. 
The information contained in this document is believed to be accurate in all 
respects but is not warranted by Mite1 Corporation (MITEL@). The informa- 
tion is subject to change without notice and should not be construed in any 
way as a commitment by Mite1 or any of its affiliates or subsidiaries. Mite1 
and its affiliates and subsidiaries assume no responsibility for any errors or 
omissions in this document. Revisions of this document or new editions of it 
may be...

Table of Contents 
1. 
2. INTRODUCTION 
General ............................................................... 
102 i-l 
ReasonforReissue ...................................................... 
102 l-l 
CUSTOMER DATA ENTRY FORMS 
General ............................................................... 
102 2-l 
Physical Configuration 
.................................................... 102 2-l 
Programming Errors 
....................................................... 102 2-3 
Exit From Error Mode...

Customer Data Entry Forms 
iv Revision 0 9104-091-l 02-NA Issue 3  

1. INTRODUCTION TO THE ADDENDUM 
GENERAL 
1.1 This document amends the existing documentation set for the SX50@ 
DPABX, PN 9104-091-l 06, Issue 5, March 1993. 
The addendum is issued to update and correct information contained in the 
above specified documentation set. 
. 
REPLACEMENT PAGE ADDENDUM INSTRUCTIONS 
1.2 Refer to the “List of Revised Pages” and remove each page listed in 
sequence and replace with Revision 1. 
Include “List of Revised Pages” in the front of Volume 1 of the system...

Addendum 
.’ 
2 
Revision 0 9104-972-OlSNA Issue 1  

4 
’ 
SYSTEM CONFIGURATION 
General 
4.1 The SX-50 system supports typical PABX applications within the following limits: 
I 
Up to 160 lines, which can be: 
l ONS Lines: 16 per slot, up to 160 if slots are available 
l OPS Lines: eight per slot, up to 80 if slots are available 
l DNIC Lines: eight per slot, up to 32 if slots are available 
. COV Lines: eight per slot, up to 64 if slots are available 
Note: The combined total number of COV and DNIC line cards must not exceed eight. 
Up to 80 trunks,...

General Descrintion 
I 
Identifying Software Without a System Console 
4.3 To identify software without the use of a system console perform the following steps: 
1. Enter the programming access code from the test line (SUPERSET 4 and 
SUPERSET 420 only). 
2. Enter command 999. The LCD display will show the software’identifier. 
Card Configurations 
4.4 
Peripheral cards can be installed in slots one through ten. The SX-50 is virtually a 
non-blocking DPABX. For optimum performance under heavy traffic...

Customer Data Enty FOGS 
COMMAND 100 SYSTEM OPTIONS PROGRAMMING 
r 
-Register 14 SYSTEM MESSAGE DETAIL RECORDING (SMDR) 
- SMDR System Enable 
0 = Disable 
1 = Enable Incoming Trunks Calls Only 
2 = Enable Outgoing Trunks Calls_Only 
3 = Enable Both Incoming and Outgoing Trunk Calls 
-- Record Meter Pulses 
0 = Disable, 1 = Enable 
- Local Call Indicator 
0 = Disable, 1 = Enable . 
-- Incoming Calls Record Only COs 
0 = Disable, 1 = Enable 
- Drop Calls of less than 8 digits (see Note below) 
I 0 =...