Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

‘: :::... . .  .
Step
1
2
3
-~~~
otccess MAINTENANCE
spplication.
Press 1[SYSTEM softkey).
Press 1 (SET softkey).
4Press 2 (TIME softkey).
5
6Enter time in either
12- or 24-hour format.
Press 0 (ENTER softkey).
7
8Repeat Step 3 through
Step 5.
Press 1 (PM softkey).
9Press 0 (ENTER softkey).Setting System Time
2.05System time may be set from the Maintenance Terminal. The
new time will be reflected on the Maintenance Terminal display,
the Attendant Console LCD display, and the 
SUPERSET 4 telephone
LCC...

System Test Procedures: .>;;.:Setting System Time
2.05System time may be set from the Maintenance Terminal. The
new time will be reflected on the Maintenance Terminal display,
the Attendant Console LCD display, and the 
SUPERSET 4 telephone
LCL’ display. Chart 2-3 shows the steps for testing setting of system
time.
CHART 2-3
SETTING SYSTEM TIME
StepActionVerify
1Access MAINTENANCESystem responds by displaying Maintenance menu.
application.
2Press 1Softkey prompts change. System Level is accessed.
(SYSTEM...

SECTION MITLSI 09-094-320-NAChanging Passwords
2.06Passwords may be changed by a user for his or her access
level, and all lower access levels. At the INSTALLER access
level, all passwords may be changed. Chart 2-4 shows the steps for
testing changing passwords at the INSTALLER level. If a different ac-
cess level is chosen, only those levels equal to or below the chosen
level will be available for testing setting of passwords.
CHART 2-4
CHANGING PASSWORDS
StepActionVerify
1Access MAINTENANCESystem...

System Test Procedures;tep IActionCHART 2-4 (CONT’D)
CHANGING PASSWORDSIVerifv
7
10
11
Enter Installer levelPassword is not displayed.
password and pressCommand line responds with:
RETURN.Enter New Password then press RETURN/ENTER:
Enter new Installer
password and press
RETURN.
Enter new Installer
password again and press
RETURN.
Repeat Steps 3 through 9NOTE: When setting passwords for a lower level than the
for remaining levels ofcurrent level of access, the prompt “Enter old Password
access...

SECTION MITL9109-094-320-NASetting Maintenance Terminal Port Baud Rate
2.07 The baud rate of the Maintenance Terminal port may be
changed from the value set at the time of 
login. Any one of six
baud rates may be chosen: 300, 600, 1200, 2400, 4800 or 9600 baud.
Note that this operation changes the baud rate of 
,the Maintenance
Terminal port only; the baud rate of the terminal itself must be
changed separately. Chart 2-5 shows the steps for testing changing of
the Maintenance Terminal port baud rate....

System Test Procedures
CHART 2-5 (CONT’D)
SETTING MAINTENANCE TERMINAL PORT BAUD RATE
StepActionVerify8Check to ensure terminal
speed is the same value as
the maintenance port; if
different, change terminal
speed to coincide with
selected Maintenance Port
value.
9Press RETURN.Command line clears and softkey prompts return to
System Level format.
10Press 6 (QUIT softkey) toTest completed.
return to Maintenance
menu.
Page 11 

SECTION MITL9109-094-320-NASetting Printer Port Baud Rate
2.08 The baud rate of the Printer Port may be changed from its
default value of 1200 baud. Any one of six baud rates may be
chosen: 300, 600, 1200, 2400, 4800 or 9600 baud. Note that this opera-
tion changes the baud rate of the Printer Port only; the 
b,3ud rate of
the printer itself must be changed separately. Chart 2-6 shows the
steps for testing changing of the Printer Port baud rate.
CHART 2-6
SETTING PRINTER PORT BAUD RATE
StepActionVerify...

System Test Procedures
CHART 2-6 (CONT’D)
SETTING PRINTER PORT BAUD RATESt@P IActionVerify
8Ensure printer speed
coincides with selected
printer port speed. If
speeds do not coincide,
either change printer
speed, or repeat Steps 8
and 9, selecting a printer
port speed which coincides
with the selected speed of
the printer.
Press 6 (QUIT softkey) to
return to Maintenance
menu.Test completed.
Page 13 

SECTION MITL9109-094-320-NASuspending Printer Device
2.09 The print device may be suspended from printing either by
specifying its 
PLID or its port along with the SUSPEND-PRTR
command.
CHART 2-7
SYSTEM LEVEL: SUSPEND-PRTR COMMAND
StepActionVerify
1Access MAINTENANCESystem responds by displaying Maintenance menu.
application.
2Press 1 (SYSTEM softkey).Softkey prompts change. System Level is accessed.
3Press 5 (SUSPEND-PRTRCommand line responds with:
softkey).
SUSPEND PRTSand 
softkey prompts change....

System Test ProceduresResume Print Device2.10 The print device may be commanded to resume printing by
specifying either its 
PLID or its port and the RESUME-PRTR
command.
CHART 2-8
SYSTEM LEVEL: RESUME-PRTR COMMAND
StepActionVerify
1Access MAINTENANCESystem responds by displaying Maintenance menu.
application.
2Press 1 (SYSTEM softkey).Softkey prompts change. System level is accessed.
3Press 7 (RESUME-PRTRCommand line responds with:
softkey).
RESUME-PRTRand 
softkey prompts change.
4Press 7...