Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDE)
4.177 Commands
6-QUIT: Pressing the QUIT softkey exits from the form.
8-SEL. OPTION: Pressing the SELECT OPTION 
softkey displays the Link
Descriptor Options 
subform for the descriptor on the command line.
O-REVIEW:Pressing the REVIEW softkey displays the Review List
subform for the descriptor on the command line.
Page 169 

SECTION MITL9109-094-210-NALink Descriptor Options for Form 42
TABLE 4-64
LINK DESCRIPTOR OPTIONS FOR FORM 42
CDE TERMINAL DISPLAY
‘II :Ol PM 15-JAN-88alarm status = NO ALAIW
‘[ LINK DESCRIPTOR NWIBER : 11IN/CUT GOINGAlarm 
debounce timer(300 - 3200 ms)B8ZS zero code suppression
Slip rate - maintenance limit( 0 - 9000 ) /24 hrs
Slip rate - service limit( 0 - 9000 ) /24 hrs
Slip rate - network sync limit( 0 - 9000 ) /24 hrs
BER - maintenance limit(IO**-n , n = ( 3,4,5,6 )I / hour
BER - service...

Customer Data Entry (CDE)
8-CONFIRM: This softkey appears when an option value has been
changed. Press the CONFIRM 
softkey to enter the change in the data-
base.
O-ENTER:Pressing the ENTER softkey (or the RETURN key on a
terminal) stores the changed parameter in the database.
4.180 Option Descriptions
Alarm 
Debounce Timer
The Alarm 
Debounce Timer defines the length of time a fault condition
must be present before it is reported to the main controller. The range
of the timer is 300 to 3200 ms.
The...

SECTION MITL9109-094-210-NAFraming Loss Limits
Framing loss occurs when the digital trunk cannot find the proper
framing bit sequence in the incoming bit stream. It is thus unable to
ensure correct decoding of the channels. There are 2 framing loss
limits maintenance and service. The framing loss error rate is between
0 and 9000 losses over a 24 hour period.Limit Definitions
Maintenance:When a maintenance limit is exceeded, the system
generates a maintenance log.
Service:When a service limit is exceeded,...

Customer Data Entry (CDE)
Review List for Form 42
4.181 The review form provides a list of users for each descriptor,identified by their physical location. There are no fields that the
programmer can edit.TABLE 4-65
II:01 PM 15-JAN-88REVIEW LIST FOR FORM 42
CDE TERMINAL DISPLAY
alarm status = NO ALARM: LINK DESC NO:
011BAYSLOTCOMMENTS2-3-
4-5-
i-WIT7-8-9-O-ENTER
ATTENDANT CONSOLE DISPLAY
4.182 Field Description:
The header line identifies the link descriptor
being reviewed.BAY, SLOT: These fields list...

SECTION MITL9109-094-210-NAForm 43 
- Tl Link Assignment
4.183 This form assigns one of the ten link descriptors to each link.
TABLE 4-66
FORM 43 
- Tl LINK ASSIGNMENT
CDE 
TERMII\!AL DISPLAY
11 : 01FM15-JAN-88alarmstatus=NO ALARM
TRUUK TYPEBAYSLOTLINK DESC Nlhl
COMMENTS
l-2-3-4-5-
6-QUIT7-8-9-0-EMERATTENDANT CONSOLE DISPLAY
TRUUK TYPEBAY
SLOTLINK DESC NWl
COMMENTS
[BLANK]
I>2>3>4>6xlJlT7>8>9>FGNTER4.184 Field Description
TRUNK TYPE: This field cannot be edited.
BAY, SLOT: This field lists the Bay and...

Customer Data Entry (CDE)base.O-ENTER: This 
softkey appears after the programmer has entered a
Link Descriptor Number for a Tl trunk card.Page 175 

SECTION MITL9109-094-210-NAForm 44
- Tl Network Sync
4.186 This form determines the order in which the links will be used
as the network synchronization clock source. When the error
threshold of the first clock source is crossed, the second clock is used
as the sync source, etc.
TABLE 4-67
FORM 44 
- Tl NETWORK SYNC
CDE TERMINAL DISPLAY
II:01 PM 15-JAN-88alarm status = NO ALARM
DESCR I PTORBAY
SLOTCOMMENTSFirst clock source
Second clock source
Third clock source
Fourth clock source
Fifth clock source...

Customer Data Entry (CDE)
8-CONFIRM: This softkey appears when an option value has been
changed. Press the CONFIRM 
softkey to enter the change in the data-
base.O-ENTER: This 
softkey appears after the programmer has entered a Tltrunk card Bay/Slot location as a clock source.
Page 177 

SECTION MITL9109-094-210-NAPage 178