Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Customer Data Entry (CDErTABLE 5-l (CONT’D)
PROGRAMMING ERROR MESSAGES
Error Message
comnent sNon-existent account code
value has been entered.
Mean i ngCDE Forms are not saved.
During a search in Form 32, CDE Data Print,
the entered Account Code does not exist.
Select another Account Code.
No 
NCIN-DIAL-IN trunk cards are A card that supports Non-Dial-In Trunks must
programnedbe defined in Form 01, System Configuration.
No STATION or 
SUPERSE-T cardsA card that supports Rotary Dial or DTMF sets
are...

SECTION MITL9109-094-210-NATABLE 5-1 (CONT’D)
PROGRAMMING ERROR MESSAGES
Error Message
Meaning
failure; data was not writtenthe system and re-enter CDE Mode.
to disk
Print Option out of range.In Form 32, Customer Data Print, there are
Valid range is
(1- 50).
only 50 Print Option numbers. Select a new
Print Option number.
This printer specification has
System already contains printer parameters.
already been programned.
Recording 
1 Start Time must beThe values for these two i terns must be> = Delay For...

Customer Data Entry (CDE)
TABLE 5-l (CONT’D)
PROGRAMMING ERROR MESSAGES
Error MessageMeaning
existdisplayed, as requested via the FIND SUPER
key, because this access code has not been
assigned to a supervisor.
TENANT NUIBER is out of range.
IThere are a maximum of 25 Tenant Groups.
Valid is 1 to 25.-1The 
TREK NWIBER XXX is
already assigned
The 
TRUUK NUMBER XXX has not
been assignedTrunk numbers can be assigned to only one
trunk. Trunk numbers are assigned in Form 14,
Non-Dial-In Trunks and Form 15,...

SECTION MITLSI 09-094-210-NATABLE 5-l (CONT’D)
PROGRAMMING ERROR MESSAGES
Error Message
Mean i ngThe value XX is outside theThe selected timer value is invalid. Refer to
valid range for the selectedTable 4-25, Trunk Hardware Options for a list
tirer optionof valid timer values.
The value XX is outside validThe selected slot number is invalid.
range for SLOT 
(I - XX)The value XX is outside validIn Form 25, ARS Route Plans, the START HOUR
range for START 
WlJR (0 - 23)specifies the starting time for each...

Customer Data Entry (CDE)
TABLE 5-l (CONT’D)
PROGRAMMING ERROR MESSAGES
Error MessageMeaningTRUUK GROUP must be enteredTo complete the Route definition, the Trunk
for a route to be defined
Group number must be specified. Refer to Form
23, ARS: Route Definition.
TREK NWIBER XX does notOnly CD trunks can be assigned as DTS in the
correspond to a CC trunkSUPERSET Telephone Lines form.
TWK NWBER XXX is a memberThe selected trunk number is a member of the
of TRUUK GROUP Xx.Trunk Group shown. A trunk number...

SECTION MITLSI 09-094-210-NA
H
:
vidPTABLE 5-1 (CONT’D)
PROGRAMMING ERROR MESSAGES
Error Message
‘ange (I-99)
Mean i ng
lerified account codes systemIn Form 33, Account Code Entry, the Accountoption must be enabled first.Code can only be modified if System Option 05,
Verified Account Codes is enabled. Refer to
Form 04, System Options/System Timers.
iarning: This path will beThe user attempted to QUIT this form with
leleted unless 1st two status“Access Code for This ACD Path” or “Primary
ines are...

MITEL STANDARD PRACTICESECTION MITL9109-094~320-NAIssue 1, April 1988
SX-200” DIGITAL
PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX)
SYSTEM TEST PROCEDURES
@Copyright 1988, MITEL Corporation. All rights reserved.
T”Trademark of MITEL Corporation
‘Registered Trademark of MITEL Corporation 

SECTION MITL9109-094-320-NA
NOTICEThe information contained in this document is believed to be accurate in all respects but is
not warranted by 
Mite1 Corporation (MITEL). The information is subject to change without
notice and should not be construed in any way as a commitment by 
Mite1 or any of its
affiliates or subsidiaries. 
Mite1 and its affiliates and subsidiaries assume no responsibility
for any errors or omissions in this document. Revisions of this document or new editions of
it may be issued...