Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation InformationTAB1E&M TRUNK MODUL
FunctionPABX to Line Gain
3 dB
-13 dBLine to PABX Gain
-4 dB-11 
dBTermination
600 ohmComplex
Transmission
2 wire
4 wire
Signaling
Type 1
Type 50= open, 
I= closet,x= not applicable
E 5-6E SWITCH SETTINGS
Switches12345678
oxxxxxxx
Ixxxxxxx
xoxxxxxx
xlxxxxxx
xx10xxxx
xx01xxxxxxxxlxxx
xxxxoxxx
xxxxxlxx
xxxxxoxx
Page 95 

SECTION MITL9109-094-200-NA
ZzEz-
-D----MUSIC ON
HOLD/PAGER
MODULERECEIVER/RELAY
CONSOLEMODULEMODULE-SWITCH
LED’s000
UNIVERSAL CARD
KAOOZlEOROFigure 5-23 Universal Card and Modules
Page 96 

Shipping, Receiving, and installation Information
Figure 5-24 Installation of Module onto Universal Card
Page 
97 

SECTION MITL9109-094-200-NACROSS-CONNECTION
MODULE MODULE
FIELD FIELDT/R PAIR
GN
T24--LINE
9.2=
aCONSOLE
T3MODULAR
NO CONNECTIONSJACK
CONSOLE MODULE
R3DIGITAL
LINE
CARDT2
R2GN 
----
RSUPERCONSOLE 1000pRCONSOLE 1000pATTENDANT CONSOLE
NDANT CONSOLE
I
MUSIC’ 
MIAo;;s -IIN1
, MIB-PA
SVSTEM
ICONTACT RATING i ;q$-!300 OHMS,
MU_SIC-ON_ H_OLp/PAGlNG_ M_OD_UL_E _
II
CONTROLIPAIR
‘CUSTOMER-SUPPLIED 
EGUIPMENTL-----------FROM 533 ON BACKPLANE----------_-(UNIVERSAL CABINET ONLV)I
(NIGHT BELL CONNECTION)
icil
Q...

Shipping, Receiving, and Installation Information
CHART 5-21
INSTALL FLOPPY DISK DRIVE PN 9109-124-000Remove or install diskette in drive while power is on and LED is off.
Remove power from the Bay before removing or installing a disk drive.
StepAction
Comments
1.While wearing antistatic wrist strap, unpack and
inspect new disk drive.
2.Install drive into its slot in Bay 2, and secure itInstall second disk drive in Bay 1.
with its latch and locking screw.
3.If installing drive into an SX-200 weldedDisk...

SECTION MITL9109-094-200-NA
LOCKING
SCREW
PN9109-124-000
8536ElMFigure 5-26 Floppy Disk Drives
Page 100 

Shipping, Receiving, and Installation InformationPOWER /’CABLE
RIBBON 
-CABLEGROUND
WIRE
KAOlB6EOROFigure 5-27 Disk Drive Connections
Page 101 

SECTION MITL9109-094-200-NACHART 5-22
UNPACK AND INSTALL PRINTED CIRCUIT CARDS
WARNING
ANY CONNECTION OF AN ONS LINE CARD, A DIGITAL LINE CARD, OR A COV LINE CARD, TO AN
OFF PREMISE APPLICATION, AN OUT OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED
PLANT APPLICATION MAY RESULT IN A SAFETY HAZARD, AND/OR DEFECTIVE OPERATION,
AND/OR EQUIPMENT DAMAGE.
StepAction
Comments
CAUTION: Do not open or unpack any printedTHE ANTISTATIC WRIST STRAP
circuit card cartons unless you are wearing
MUST BE CONNECTED TO...

Shipping, Receiving, and Installation Information
CHART 5-22 (CONT’D)
UNPACK AND INSTALL PRINTED CIRCUIT CARDSStepActionComments
8.480-PORT CONFIGURATIONInstall Digital Interface 
Cards (DIC) in Bays 3, 4,
and 5. Connect PCM cables to their associated
DIC (each PCM cable connector is labeled to
identify the DIC it connects with).
336-PORT CONFIGURATION
Install Bay Control Card (BCC), Bay Power
Supply (BPS), and PCM cables to each digital
Bay.
456-PORT CONFIGURATION
Install Bay Control Card (BCC) and Bay...

SECTION MITL9109-094-200-NA
7105EOROFigure 5-28 Printed Circuit Card Packaging
Page 104