Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
CHART 5-11
PFT KIT INSTALLATION INSTRUCTIONS - UNIVERSAL CABINET
StepAction
Comments
1.Unlock and open rear door of cabinet.
2.Attach antistatic wrist strap to your wrist andA PFT card is shown in Figure
carefully unpack PFT card(s).5-13.
3.Power down system.
4.Place PFT card into the upper position, identify Following this sequence minimizes
its two mounting holes on frame, and remove
the chance of damaging a PFT
card. Refer to Figure 5-14.
card when...

SECTION MITL9109-094-200-NACHART 
j-11 (CONT’D)
PFT KIT INSTALLATION INSTRUCTIONS 
- UNIVERSAL CABINET
StepAction
Comments
14.Connect the ALARM pair of the IntercabinetDo not connect the intercabinetCable Assembly (672 port) to TBI-1 and 
TB’l-3 Cable Assembly (672 port) to J2 if
of the lower (third) card in the Control cabinet; there are no PFT cards in the
in the peripheral cabinet, connect thePeripheral cabinet.
Intercabinet Cable Assembly (672 port) to
TBl-2 and TBI-4 of the upper card. Connect
the...

Shipping, Receiving, and Installation Information
. . . . . . . _ . . . . .
0
0
OPTIONAL 
LWGS CONVERSION MODULE FOR PFT CARD
8538E2R2Figure 5-13 Power Fail Transfer Card
Page 75 

SECTION MITLSI 09-094-200-NA
CARD
FILELOOP START
GROUND START
CONVERTER
TBlRIGHT HAND SIDE
OF CABINET
(FROM REAR)
Figure 5-14 Locating PFT Card in an SX-200 Universal Cabinet
Page 76 

Shipping, Receiving, and Installation Information1
-
-
1
KAO700ROEOFigure 5-15 PFT Card Connections
Page 77 

SECTION MITL9109-094-200-NACHART 5-12
INSTALL BAY 5
StepActionComments
1.Unpack shelf. Check backplane for cracks, bent
pins, loose or missing items, and other
damage. Check hardware against packing slip.
Check fuses (if supplied).
2.Set POWER and BATTERY switches off and
remove line cords from AC outlets.
3.Unlock and open front door. Attach ground
wire to side of shelf before installing shelf into
cabinet.
4.Place shelf onto shelf guides.
5.Fasten shelf to equipment cabinet using eight
screws.
6.At...

Shipping, Receiving, and Installation Information
CHART 5-13
ANALOG PERIPHERAL CABINET RESERVE POWER SUPPLY INSTALLATION
WARNING
RESERVE SUPPLY IS FOR ANALOG PERIPHERAL CABINET ONLY. DO NOT ATTEMPT TO CONNECT
IT TO CONTROL CABINET OR DIGITAL PERIPHERAL CABINET, WHICH REQUIRES A UPS.
CAUTION: Check that the BATTERY switch on the reserve battery pack is set to OFF. Checkthat the three switches on the battery charging unit are set to OFF.
StepAction
Comments
1.Unpack reserve power supply equipment....

SECTION MITL9109-094-200-NAStep
18.
19.
20.
21.
22.
23.
24.
25.Close and lock all cabinet doors.
26.Place cabinet in final position.CHART 5-13 (CONT’D)
ANALOG PERIPHERAL CABINET RESERVE POWER SUPPLY INSTALLATION
ActionComments
Connect the Red, Black and Green leads.
Route the charging unit power lead to the
adapter, and plug the adapter into the
receptacle on the rear door power supply.
Plug system power cord into its receptacle.
On Battery Pack, set BATTERY switch to ON.
On Charging Unit, set AC switch...

Shipping, Receiving, and lnstallatien hIfOrmatiOn -Figure 5-16 Charging Unit
:.,.:
Page 81 

IlTLSl OS-094~ZOO-NACHART 5-17
INSTALL MAINTENANCE TERMINAL TO AN 
SX-200 CONTROL CABINET
Action
Unpack and install the maintenance terminal
(VT-100 or equivalent) in its assigned position.Connect 
;rn RS-232 cable betwetn the terminal
and the local port on the maintenance panel on
, the front of the system.
If installing a remote terminal, connect a
modem to the remote port on the maintenance
panel, or on the power distribution panel at the
lower rear of the cabinet (depending on cabinet
type) Connect...