Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
CHART 5-29
SET DID/TIE TRUNK CARD OPTION SWITCHES
CAUTION: Follow the procedures outlined in paragraph 5.03 while handling printed circuit
cards or modules.Note:Complete installation forms for Trunk Card settings before setting any switches on the
card.
StepAction
Comments
1.Attach the antistatic wrist strap to your wristRefer to notes for setting of
and select the required trunk card.switches and Figure 5-39.
2.Set TRUNK BUSY switches as required for...

SECTION MITL9109-094-200-NATRUNK CONTROL SWITCHES
’
11 ABLE
~1NORMAL SETTING,-OPEN 
-\SEE TABLE
5 = CLOSED
6 = CLOSED
7 = CLOSED
9 
= CLOSED
9 = NOT USED
10 = NOT USED
.--.._-.OUTGOING INCOMING
WINKWINKSWITCH
SWgTCHA-
sw,l I  II----.iA_:6000 :---:9oos29ooaL-_--lSW3py$
SWZI I  I:I:TRUNK 1900s-lIMPEDANCE
SWITCHES
8TRUNK
BUSY
SWITCHES,
SW21 i;
TRUNK 2!.IAIMPEDANCE9OOQI nrSWITCHESTRUNK BUSY SWITCHES
NORMAL SETTING
1=CLOSED2=CLOSED3=CLOSED4=CLOSED5qOPEN
6
=OPEN
7=CLOSED8=CLOSED
5496ElRlFigure 5-39 DID 
/ TIE...

Shipping, Receiving, and installation Information
NOTES FOR FIGURE 5-39DID 
/ TIE TRUNK CARD SWITCH FUNCTIONS
1. Trunk impedance switches are located on the rear face of the Trunk Card.
Trunk Busy Switches
2. Outgoing Busy Switches (1 per trunk) can be set for either of the following conditions:
Idle setting 
-normal trunk operation
Busy setting
- trunk cannot be seized for outgoing call.
3. The “outgoing busy” condition may be set either by the outgoing busy switch (Note 
2), or
by the console “Trunk...

SECTION MITL9109-094-200-NAMARKED END
SHOWN FOR
LOOP START TRUNK
J1 ,I
IIIIITRUNK4
i
/ 10 TRUNK
I /JTR;NK
ii
I
I----I ------- -+-----1
II
I
I
0 TRUNK2I
If
 q TR;NK
IIi 
-I a
I
LEDs
C4- TRUNK 1
Ic-TRUNK 2
c_I
__ITRUNK 3
_ITRUNK 4
c
ITRUNK 5
TRUNK 6
xALARM
1
5Figure 5-40 
LWGS Trunk Card
Page 128 

Shipping, Receiving, and Installation Information
CHART 5-31
INITIAL SYSTEM POWER-ONStepActionComments
1.Check that all cards are in place and that all
cables within the cabinets, including
uninterruptable power 
supply, are connected.
2.Plug line cord(s) into AC receptacles.If Control cabinet has a UPS, plug
line cord into UPS and UPS line
cord into AC receptacle, according
to manufacturer’s instructions.
3.
4.
5.
6.
7.
8.Turn on main circuit breakers and UPS.
Turn on power switch on maintenance...

SECTION MITL9109-094-ZOO-NACHART 5-31 (CONT’D)
INITIAL SYSTEM POWER-ON
StepActionComments
12.Proceed with Maintenance or CDE application,Refer to Section
as required.
MITL9109-094-35 1 -NA, RS-232
Maintenance Terminal, or Section
MITL9109-094-210-NA, Customer
Data Entry.Note:
The console may be connected to the console jack on the front of the maintenance panelfor working on the PABX, rather than being at the usual attendant console location. This
jack is wired to the default 
DLIC console position (Bay...

Shipping, Receiving, and Installation Information-Before using a disk, it must be acclimatized for 24 hours in the
environment in which it will operate
-System power must be on before inserting a disk into or re-
moving a disk from the drive
-Whenever the disk is to be removed or inserted, ensure that
there is no read or write activity in progress from the system,
the LED on the disk drive must be OFF.
CHART 5-33
REPACKING FOR SHIPMENT
StepActionComments
Note: Do not disconnect the system groundWhenever...

SECTION MITL9109-094-200-NA
DISKETTEREMOVALPOSITIONPUSH TO
RIGHT AFTER
INSERTING
DISKETTE7701 
EZRlFigure 5-41 Disk Drive Latches
Page 132 

Shipping, Receiving, and Installation Information
6. CABLING AND CROSS-CONNECTIONSGeneral
6.01This Part details the cabling and cross-connections required
when installing the SX-200 DIGITAL PABX.Telephone Set and Trunk Cabling
6.02 Telephone set and trunk cabling terminates on the building
cross-connect terminals in the normal manner.System Cable Terminations
6.03 All interconnecting cables must be terminated in accordance
with the following tables according to the number of bays
supplied and equipped....

SECTION MITL9109-094-200-NATABLE 6-l
CONTROL SHELF TIP 
& RING ASSIGNMENTS
Plugs 
55 and J9 for Digital Bays 1 through 7 (J25 for COMBO Bay 2)
SlotPlug
655or
8
J9or
4525
555or
7J9or
3525
Pin
26W-BL1BL-W
27w-o2o-w28W-G
3G-W
29W-BR
4BR-W
30w-s5s-w31R-BL
6BL-R32R-O7O-R33R-G
8G-R34R-BR9BR-R
35R-S
10S-R
36BK-BL11BL-BK37BK-0120-BK
38BK-G
14BR-BK
40BK-S15S-BK41Y-BL16BL-Y42Y-O
17O-Y43Y-G18G-Y
44Y-BR19BR-Y
45Y-S20S-Y46V-BL21BL-V
47v-o22o-v48V-G
23G-V
49V-BR
24BR-V
50v-s25s-v
Cct
1TlRI
2T2R2
3T3
R3414
R4...