Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
CHART 5-23
INSTALL A MAIN CONTROL CARD
CAUTION: Always wear a properly grounded antistatic wrist strap when handling a printed
circuit board (pcb); the PABX #6 AWG ground wire must be correctly connected to
an approved ground as described in the installation manual.
CAUTION: Remove conductive articles such as rings and watches before handling the Main
Control Card (MCC).CAUTION: Hold a pcb by its non-conductive edges, and avoid touching the components or...

SECTION MITL9109-094-200-NACHART 5-23 (CONT’D)
INSTALL A MAIN CONTROL CARD
StepAction
Comments
7.Install the Decryption module; there are no
standoffs for it.
8
1.
2.
3.
Install a Tl Clock Module.Refer to Figure 5-30.
MODULE REMOVAL 
- Read this BEFORE
attempting to remove modules
Pop the module pcb from the standoffs byThis “pinching action” avoids
applying pressure with your thumb onto thebending the pcb any more than is
short portion of the standoff projecting throughnecessary to release it from...

Shipping, Receiving, and Installation InformationDECRYPTIONMODULE
KAOCWEOAOFigure 5-29 Installation of Modules onto an MCC
Page 107 

SECTION MITL9109-094-200-NA
0Attach wrist strap
@ At top front of card, locate
connector 54; remove the jumper
clip from within the connector.
0Place the standoffs into theTl clock module, flanged end.
Place themodule
overJ4 an
holes, and press into place,applying gentle even
pressure over connector 
- DO NOT BEND OR FLEX PCB.
0Press standoffs into place also.
KAO65lEOR
Figure 5-30 Installation of a Tl Clock Module onto an MCC
Page 108 

SECTION MITL9109-094~ZOO-NATl TRUNK CABLE
TO CHANNEL SERVICE
0c-- CABINET
SIDE RAIL
Tl ADAPTER
CABLE ASSEMBLY
UNITTl
ADAhER CARD
KA0653EZRZ ,
Figure 5-32 Installation of a 
Tl Adapter Cable Assembly
Page 110 

Shipping, Receiving, and Installation Information2 Replace the screws and
washers with the hex slotted
standoffs in the kit. Do not
place a washer under the
standoff. Tighten the standoffs
with a screwdriver, firm
but do not overtighten.1 Remove the 
stxews and
metal cable strain relief,
CAUTION: care must be
taken not to remove the
connector plastic shroud.
3 Plug the Tl Adapter Card into the
Backplane connector. Fasten the
card using the two screws and the
washers in the kit.
KAO652ElR’Figure 5-33...

SECTION MITLSI 09-094-200-NACHART 5-25
INSTALLATION OF MODEM POOLING ON AN SX-200 DIGITAL PABX
StepActionComments
For rack mounted 
DATASET 2102
1.Install the rack mounted data sets as
required.Refer to Figure 5-34.
2.
3.Install a Modem Interconnect Panel.
Connect a Modem Adapter to the RS-232
port on the 
DATASET 2102.
4.Connect the Modem to the Modem
Adapter with an RS-232 cable.
5.Connect the Modem LINE plug to the
FROM MODEM jack of the Modem
Interconnect Panel.
6.
7.Connect the DATASET plug of...

Shipping, Receiving, and installation Information
ONS
rLINE
CARD
&II. 11ODEM b.-..---IvALmr I cn
I
;Cl 4--PHONEIINTERNAL
DATASETClRCUlTRV
RED
GREENYELLOW
BLACK
RS-232 CABLE
TELEDAPT
JACK
VOICE PATH 
- RED/GREENMI/MIC - BLACKIYELLOW
KA0723EOROFigure 5-34 Modem Pooling with a Standalone 
DATASET
Page 113 

SECTION MITL9109-094-200-NA4-WIRE TELEPHONE LINE
CORDRACK MOUNTED
DATASET4-WIRE TELEPHONE LINE CORD
FOR 
MI/MIC (BLK/V)TO id PAIR
CABLE 
IVIASHELF) TO
DIGITAL
LINE CARDFROM MODEMII
Jl TO ONS
LINE CARD
TO 
DATASET
KA0722ROEOFigure 5-35 Modem Pooling with Rack Mounted 
DATASET and Modem Interconnect Panel
Page 114