Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
7. UPGRADING AN EXISTING SX-200 PABX TO AN SX-200 DIGITAL PABX
Strategy7.01The control cabinet will be installed beside the existing SX-ZOOPABX cabinet, equipped with the new attendant console, new
stations, 
tru-rks, or features for Bays, 1, 2 or 3, and powered up. All
testing can be completed and the new database entered with CDE,
including all equipment in the existing SX-200 system. The existing
SX-200 DIGITAL PABX is then reconfigured as a Peripheral...

SECTION MITL9109-094-200-NA
CHART 7-l
SX-200 PABX UPGRADE TO SX-200 DIGITAL PABX
This upgrade and installation procedure is to be performed only by qualified personnel who have
successfully completed a 
MITEL Installation and Maintenance Course for the SX-200 DIGITAL
PABX.StepActionComments
1.Unpack the Control cabinet and place it in
its assigned location according to Chart5-4.
2.Relocate the #6 AWG system ground to
Note: Connect a temporary jumper
the common ground stud in the Control
between the...

Shipping, Receiving, and installation Information
CHART 7-1 (CONT’D)
SX-200 PABX UPGRADE TO SX-200 DIGITAL PABXStepActionComments
10.Connect the printer cable, if present, to
J29 on the Control Shelf backplane.
11.Remove all rtxisting consoles from the
system and repack them.
12.Connect a PFT monitor wire between PI8of the Interconnect Card and TBI-7 of the
PFT card in an SX-200 cabinet. In an
SX-100 cabinet, connect the PFT monitor
wire between 
PI8 and J14.
13.If peripheral shelf card assignments are...

SECTION MITL9109-094-200-NAPage 148 

Shipping, Receiving, and installation Information
8. UPGRADE A 336 PORT PABX TO A 672 PdRT PERIPHERAL CABINET
General
8.01This upgrade and installation procedure is to be performed onlyby qualified personnel who have successfully completed a
MITEL Installation and Maintenance Course for the SX-200 DIGITAL
PABX.
8.02This procedure identifies how to convert an existing 336-port
PABX Control cabinet to a 672-port PABX Peripheral cabinet;
the actual installation of the 672-port PABX is described in Section...

SECTION MITL9109-094-200-NACHART 8-l (CONT’D)
CONVERT A 336 PORT CONTROL CABINET TO A 672 PORT PERIPHERAL CABINET
StepAction
Comments
4.Open the front door, and put on the antistatic
wrist strap. Remove all cards from the cabinet,
storing each in an antistatic bag. Place in a
safe and secure location until required for
installation.
5.
6.Remove the panel (if present) above the upper
card file (2 screws).
Remove the upper (Peripheral) 
cardfile (if
present).
- Identify and record all ground connections...

Step
(Cognt’d
10.
11.
12.
13.Action
- Remove the PFT harness assembly from the
PFT card and tie wrap harness to Control
cardfile.Comments Shipping, Receiving, and Installation Information
CHART 8-l (Cont’d)
CONVERT A 336 PORT CONTROL CABINET TO A 672 PORT PERIPHERAL CABINET
- Remove the temperature sensor assembly, if
present, and tie wrap it and its wiring
harness to the Control cardfile.
- Remove the screws at the front, and slide
the 
cardfile and attached assemblies out.Remove the 
#6 AWG ground wire...

SECTION MITL9109-094-200-NACHART 8-l (Cont’d)
CONVERT A 336 PORT CONTROL CABINET TO A 672 PORT PERIPHERAL CABINET
StepAction
Comments
14.Install the larger Blanking panel at the topfront of the cabinet using 2 IO-32 screws
provided.
15.Remove the cover plate on the right side of
the cable exit panel at the back of the cabinet.
If the panel was a flat one replace the cover
plate with the cable adapter plate. Fasten theplate with 6 
#6-32 self-tapping screws with
an external tooth lockwasher under each...