Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

MITEL STANDARD PRACTICESECTION MITL9109-094-206-NAIssue 1, 
April 1988
SX-200” DIGITAL
PRIVATE AUTOMATIC BRANCH EXCHANGE (PABX)
INSTALLATION FORMS
@Copyright 1988, MITEL Corporation. All rights reserved.
““‘Trademark of MITEL Corporation
‘Registered Trademark of MITEL Corporation 

SECTION MITL9109-094-206-NA
NOTICEThe information contained in this document is believed to be accurate in all respects but is
not warranted by 
Mite1 Corporation (MITEL). The information is subject to change without
notice and should not be construed in any way as a commitment by 
Mite1 or any of its
affiliates or subsidiaries. 
Mite1 ‘and its affiliates and subsidiaries assume no responsibility
for any errors or omissions in this document. Revisions of this document or new editions of
it may be issued...

Installation Forms
1. INTRODUCTIONCONTENTSPAGE
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Reason for Issue . . . . . . . . . . . . . . . . . . . . . . . . e . . . . . . . . , . . . . 1
Section Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . 1
2. SYSTEM INITIALIZATION
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. CUSTOMER DATA ENTRY FORMS
General . . . , ....

SECTION MITL9109-094-206-NALIST OF TABLES (CONT’D)
TABLETITLE
PAGE3-30
3-31
3-32
3-33
3-34
3-35
3-36
3-37
3-38
3-39
3-40
3-41
3-42
3-43
3-44
3-45
3-46
3-47
3-48
3-49
3-50
3-51
3-52
3-53
3-54
4-l
4-2
4-3
4-4
5-15-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-11
5-12Form 23 
- ARS: Route Definition.................56Form 24 
- ARS: Route Lists.....................57Form 25 
- ARS: Route Plans....................58Form 26 
- ARS: Digit Strings....................59Form 
26~- ARS: Nested Digit...

installation Forms
CHART
2-l
2-2
FIGURE
4-l
4-2
4-3LIST OF CHARTS
TITLEPAGE
initial Power-Up Procedures from the Terminal . . . . . . . 4
Initial Power-Up Procedures from the Attendant Console 5
LIST OF ILLUSTRATIONS
TITLEPAGECO Trunk Card Switch Functions . . . . . . . . . . . . . . . . . 93
E&M/Tie Trunk Card Switch Functions . . . . . . . . . . . . . 96
DID/Tie Trunk Card Switch Functions . . . . . . . . . . . . . . 99 

SECTION MITL9109-094-206-NA
vi 

installation Forms
1. INTRODUCTIONGeneral
1.01This document contains the forms required to install and pro-
gram the 
SX-200@ DIGITAL PABX with Generic 1003 software.
These forms differ from those that appear on the CDE terminal; they
are intended for planning prior to data entry. Forms which cannot be
edited are excluded from this Section; specifically, Review List for
Form 09, Review List for Form 11, Review List for Form 13, Review Listfor Form 29, Review List for Form 30, Form 32 Customer Data...

Installation Forms
2. SYSTEM INITIALIZATIONGeneral
2.01When the system is first installed, the default data must be
loaded into the system. Refer to Chart 2-1, Initial Power-up
Procedures From the Terminal, Chart 2-2, Initial Power-up ProceduresFrom the Attendant Console and to Section 
MITL9109-094-200-NA,
Shipping, Receiving, and Installation Information for details.
Page 3 

SECTION MITL9109-094-206-NACHART 2-l
INITIAL POWER-UP PROCEDURES FROM THE TERMINAL
1. Ensure that the correct Decryption Module is installed. Refer to Section
MITL9109-094-200-NA, Shipping, Receiving, and Installation Information.
2. Turn power supplies ON.
3. Inset-t diskette A in the Bay 2 disk drive (left drive of 672-port Bay 0 ) and diskette B in 
Baj1 disk drive (right drive of 672-port Bay 0). Refer to the illustration on the disk drive door
for the correct diskette orientation. Do not...