Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
CHART 5-26
SET CO TRUNK CARD SWITCHES (TYPES -01 l/l 11)
CAUTION: Follow the procedures outlined in paragraph 5.03 while handling printed circuitcards or modules.
Note:Complete installation forms for trunk card switch settings before setting switches.
Step
1.
2.
3.
4.
5.
6.
7.
a.
--Action
Identify trunk circuit by card position, type, and
circuit number.
While wearing the antistatic wrist strap, removethe card from its package or from the
equipment...

SECTION MITLSI 09-094-200-NA
F AGROUNDI
qTRUNK CONTROL SWITCHES
!TRUNK 3
El
TRUNK 4
ElLOOP GROUND
START SWITCHES
_71(NOTE 6)
//0NON-MODULAR TYPE(NOTES 1 AND 2)
, TRUNK 
BUSV’A’/”SWITCHES-/’
#TRUNK 1A”TRUNK 2
OUTGOING
TRUNK 3
uTRUNK 4
3TRUNK SWITCHES ON REVERSE OF BOARD
I ILOOP;..;I 7
ElTRUNK 1
:-.TRUNK 2TRUNK 4
r...INCOMINGI  :
INDIVIDUAL TRUNK CONTROL SWITCHES HAVE MEANINGS ACCORDING
TO THE 
IDENTITV OF THE PROM INSTALLED ON THE CARD. THESE
MEANINGS ARE SHOWN IN THE FOLLOWING DIAGFlAM.3RD WIRE TRUNK 1...

Shipping, Receiving, and Installation Information
NOTES TO FIGURE 5-36 CO TRUNK CARD TYPES 91 IO-01 1 AND -I 11TRUNK BUSY SWITCHES
1. OUTGOING BUSY SWITCHES (I PER TRUNK) CAN BE SET FOR EITHER:
IDLENORMAL TRUNK OPERATION
BL’SYTRUNK CANNOT BE SEIZED FOR OUTGOING CALL.
2. THE “OUTGOING BUSY” CONDITION MAY BE SET EITHER BY THE OUTGOING BUSY
SWITCH (NOTE I), OR BY THE CONSOLE “TRUNK BUSY OUT” FUNCTION. WHEN THIS
CONDITION IS IN EFFECT THE INCOMING BUSY SWITCH AFFECTS THE TRUNK CONDITION
AS FOLLOWS:
IDLENO...

SECTION MITL9109-094-200-NA
IGNORE REVERSALS9. IF LINE REVERSALS ON THE TRUNK CIRCUIT ARE REQUIRED TO HAVE NO EFFECT THE
IGNORE REVERSALS SWITCH IS SET TO “OPEN”. IF LINE REVERSALS ARE TO BE RECOG-
NIZED THE SWITCH IS SET TO CLOSED.CHART 5-27
SET CO TRUNK CARD SWITCHES (TYPES 
-211/311)CAUTION: Follow the procedures outlined in paragraph 5.03 while handling printed circuit
cards or modules.
Note:Complete installation forms for trunk card switch settings before setting switches.
StepAction
Comments...

Shipping, Receiving, and Installation Information
TRUNK 1piiqI I
TRUNK 2 
TR2 TRlpiiqI I
OPEN
TRUNK 
BUS?
SWITCHES
SWITCHESTRUNK 4 TR4 TR3
Tc;;qI 1LQQdHIGH IMPEDANCE SWITCHES
-;TRUNK BUSY SWITCHES (NOTES 1 AND 2)
lNCOl.wvuBUSYIL--l1OUTGOING
IDLENORMAL
SETTING1=OPEN2=OPEN3=OPEN
4=OPEN5=CLOSED6=CLOSED7=CLOSED8=CLOSEDTRUNK CONTROL SWITCHES
NORMAL SWITCH
SETTING NUMBERFUNCTION
CLOSED13RDWIRETRUNK1CLOSED23RDWIRETRUNK2CLOSED33RDWIRETRUNK3CLOSED43RDWIRETRUNK4
OPEN5IGNORE REVERSALSCLOSED6RELEASE TIME...

SECTION MITL9109-094-200-NANOTES FOR FIGURE 
5-37 CO TRUNK CARD SWITCH FUNCTIONS
TRUNK BUSY SWITCHES
1. OUTGOING BUSY SWITCHES (1 PER TRUNK) CAN BE SET FOR EITHER:
IDLENORMAL TRUNK OPERATION
BUSYTRUNK CANNOT BE SEIZED FOR OUTGOING CALL.
2. THE “OUTGOING BUSY” CONDITION MAY BE SET EITHER BY THE OUTGOING 
BUSYSWITCH (NOTE 
l), OR BY THE CONSOLE “TRUNK BUSY OUT” FUNCTION. WHEN THIS
CONDITION IS IN EFFECT THE INCOMING BUSY SWITCH AFFECTS THE TRUNK CONDITION
AS FOLLOWS:
IDLENO ANSWER WILL BE GIVEN TO INCOMING...

Shipping, Receiving, and Installation Information
TYPE 911 O-21 1 IS FIXED AT 40/60 RATIO.
LOOP/GROUND CALLING SWITCHES
9. THE LOOP/GROUND CALLING SWITCHES (1 PER TRUNK) CAN BE SET TO:
LOOPUSED FOR LOOP-CALLING TYPE TRUNKS
GROUND USED FOR EARTH-CALLING TYPE TRUNKS
XT SWITCH
lO.THE XT SWITCH (1 PER TRUNK) IS USED IN CONJUNCTION WITH THE 3RD WIRE SWITCH
(NOTE 5) AND CAN BE SET TO PROVIDE THE FOLLOWING CONDITIONS:
-48 VTHE CIRCUIT RESPONDS TO A -48 Vdc SIGNAL (E.G., WHEN IT IS A METER
PULSE OR A BUSY...

SECTION MITL9109-094-200-NACHART 5-28
SET E&M/TIE TRUNK CARD OPTION SWITCHES
CAUTION: Follow the procedures outlined in paragraph 5.03 while handling printed circuit
cards or modules.
Note:Complete installation forms for Trunk Card switch settings before setting any switches on
the card.
StepAction
Comments
1.Attach the antistatic wrist strap to your wrist.
2.Select the required trunk card and set the busyRefer to notes for setting of
switches to idle or busy as required.switches and Figure 5-38.
3.Set...

Shipping, Receiving, and Installation Information
TRUNK CONTROL SWITCHES
OPEN\
‘“FIK!”Z-WIRE
iiii
u-NOT4-WIRE
‘NEllNGSPECIAL
GAIN
(NOTE 3)
r,NORMAL SETTING
1 = CLOSED
2=CLOSED3=OPEN
4=OPEN
5=CLOSED6=CLOSED7=CLOSED8=CLOSED9 = NOT USED
10 = NOT USED
N%iAL
IPN103028
600 !2l---, TRUNK 1I, IMPEDANCE
i 
i6OOi-lI-T-I1’1.y4-WIRE
9oosl
Y”“1101TRUNKBUSV
SWITCHESTRUNK CONTROL
SWITCHES
6OOcJr- ‘TRUNK2
‘IMPEDANCE
t SWITCHES-J (NOTE 1)9oof22-WIRE
r-7
I 1
I 1
6OOQ
1-JT2T;LA.24-WIRE9OOQTRUNK BUSY SWITCHES...

SECTION MITL9109-094-200-NA
NOTES FOR FIGURE 5-38
E&M/TIE TRUNK CARD SWITCH FUNCTIONS
1. Trunk impedance switches are located on the rear face of the trunk card.
2. Outgoing/incoming switch settings:Outgoing Busy Incoming Busy
Switch Set toSwitch Set to
IdleBusy
BusyBusy
Busy
Idle
IdleIdle
ResultNormal trunk operation 
-if trunk is made busy by
attendant, outgoing busy, incoming busy condition re-
sults. See below.
Trunk cannot be seized, incoming or outgoing from the
PABX. Recommended setting if trunk...