Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Here you can view all the pages of manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 31

Shipping, Receiving, and Installation Information(b)
(c)
(4
(e)
(4
(cl)
#6 AWG insulated green wire connected directly to both points
only.
The system cabinets and associated 
ducting hardware shall not
be exposed to any ground source other than that described in
subparagraph (a) above.
AC service wires bringing AC to the cabinets shall not share anenclosure or raceway with other system grounds, DC power
distribution wires, or signaling wires.
All system hardware shall be provided with connections to...

Page 32

SECTION MITL9109-094-200-NAPage 24 

Page 33

Shipping, Receiving, and Installation Information
4. CONTROL SHELF AND PERIPHERAL SHELF BACKPLANES AND WIRING
Control Shelf (with COMBO backplane - 336, 456, and 480 ports)
4.01The Control Shelf combination backplane is an integral part of
the Control Shelf and serves Bay 1 and Bay 2 to connect the
various circuit cards.
4.02The 12 Peripheral cards are arranged in two rows; the upper
row designated by square and circular identifications, and the
lower row by circular identifications. Four of the...

Page 34

SECTION MITLSI 09-094-200-NA
identical, while Bay 5 has fewer printed circuit boards. In an SX-lClO@
PABX upgrade, the SX-700 cabinet contains only Bay 4.
Analog Peripheral Shelf PCB Assignments
PCB TypeSlotsBay 3Bay 4Bay 5
Trunk or Station
Trunk or Station
DIC
Scanner
PCC1-12
X.XX
13,14,15XX
18XXX
19XX
20XX
Figure 4-9 shows wiring in the peripheral cabinet.
Figure 4-10 shows Power Fail Transfer wiring.
Figure 4-l 1 shows Peripheral cabinet backplane wiring.
4.08An Analog Peripheral Shelf may have a...

Page 35

Shipping, Receiving, and Installation InformationBAY 2 SLOT 34BAY 1 SLOT 7+8BAV 1 SLOT 5+6E4 
(DG)0
0
J,9 . . . . . . .
. .
521. . . . .. . . .. . . . . .. . . 513NOT USED. . . .JlTEMP SENSE
NOT USED
J17APCM TO
BAY 3
5178DISK DRIVECONSOLE
MAINTENANCE
PANEL
. . . .
NOT USED
. . .
I+R TEST LINE
. . .
BAY 2 SLOT 1+2BAY 1 SLOT 3+0BAY 1 SLOT I+2NOTE: 
Jl9 = LOCAL RS-232 CONNECTOR
ON MAINTENANCE PANEL
521 = REMOTE RS-232 CONNECTOR
ON MAINTENANCE PANEL
7276E4R2Figure 4-l SX-200 Welded Cabinet Control Shelf...

Page 36

SECTION MITL9109-094-200-NATO DOOR 
-
NOTE:This assembly
should 
newrbe disturbed
7696E2R2Figure 4-2 Rear View of SX-200 Control Cabinet 
- Grounding
Page 28 

Page 37

Shipping, Receiving, and Installation Information
7697EOROnI IIFigure 4-3 Rear View of SX-200 Control Cabinet 
- Power
Page 
29 

Page 38

SECTION MITL9109-094~200-NA
7696ElRtFigure 4-4 Rear View of SX-ZOO Control Cabinet 
- Signal Cables
Page 30 

Page 39

Shipping, Receiving, and Installation Information!4 (DG)0
r
BAY 2 SLOT 3+4BAY 1 SLOT 7+8BAY 1 SLOT 5+6TEMP SENSE
c
-WV:*IN.-m.-4Jv.
I
R.Z:Em.+W.0J29
Ill 25
.I!! 30ABC
15
10
15
20
25
300
P3UPS ALARM UP
El 
(EDG)0
E2 
‘DGb
.3l 1ZV:-=h-4JV.R.z.DO.4v.BAY 2 SLOT 
I+2BAY 1 SLOT 3+4BAY 1 SLOT 1+2NOTE: 
J,g TLOCAL RS-232 CONNECTOR
ON MAINTENANCE PANEL
J21 = REMOTE 
W-232 CONNECTOR
ON CABINET REAR CABLE PANEL
Figure 4-5 SX-200 Universal Cabinet Control Shelf Backplane
Page 31 

Page 40

SECTION MITLSI 09-094-200-NAFigure 4-6 Rear View of SX-200 Universal Control Cabinet 
- Grounding
Page 32 
Start reading Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

All Mitel manuals