Home > Mitel > Communications System > Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Here you can view all the pages of manual Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 21

Shipping, Receiving, and Installation Information -
2.20Four types of modules are available that can be plugged into
the Universal card. These are:DTMF Receiver/Relay Module 
-Has four Dual-Tone Multi-Frequency(DTMF) receiver circuits and two relays. The relays can be used for
night bells, alarms, etc. Module power rating is 2.Music/Paging Module 
-Provides one 600 ohm balanced audio
(music) input and a 200 ohm output, to a paging amplifier. There is
also one relay contact, which can be used for...

Page 22

SECTION MITL9109-094-200-NATX
7685EOROFigure 2-8 Digital Interface Card
Page 14 

Page 23

Shipping, Receiving, and Installation InformationMaintenance Panels
2.27Control Cabinet. The maintenance panel is located at the top
front of the control cabinet, behind the door, and contains the
following controls and connections for the PABX:
Top Shelf Power 
-controls bay 3 po.nerTest line 
- system test line (bay 2, slot 1, cct 1)
Power Fail Control Switches 
-controls source of power fail transfer
initiationMaster Switch 
-operate to TRANSFER position to force system power
fail transfer
Maintenance...

Page 24

SECTION MITL9109-094-200-NAPower Fail Transfer Control Switch 
-controls source of power fail
transfer initiation
-connector for an RS-232 terminal
Maintenance Ports Selection Switch 
- Selects whether a terminal is
connected directly to maintenance panel or through a modem to con-
nector at rear of cabinet.
2.31672-Port Peripheral Cabinet. It has no maintenance panel; the
only controls are the ON/OFF switches on the Bay Power Sup-
plies.Connecting Cables
2.32The connections between the Main Control Card...

Page 25

Shipping, Receiving, and Installation Information
(not associated with the DTMF receivers) are also provided on the
module, which can be operated under control of the program, to
control various system functions such as night bells or alarms. Eachrelay provides a contact closure across a tip-ring pair.
relay contact ratings90 Vrms at 0.1 A
48 Vdc at 0.5 A
CAUTION: This relay contact may be connected only to a secondary
circuit that has no direct connection to a primary circuit,
and receives its power...

Page 26

SECTION MITL9109-094-200-NACAUTION: This relay contact may be connected only to a secondary
circuit that has no direct connection to a primary circuit,
and receives its power from a transformer, converter, or
equivalent isolation device situated within the equip-
ment.
Alternate Music Source - ACD only
2.38An alternate music source for the Automatic Call Distribution
Feature Package must be either an FCC Part 68 and DOC ap-
proved Recorded Announcement Device which is connected to an ONS
circuit, or...

Page 27

Shipping, Receiving, and Installation Information
2.43 Installation instructions for the data cabinet are included in
Section MITL9141-753-525-NA, DATACABINET 9000, and Instal-
lation instructions for the data shelf are included in Section
MITLS 141-753-526-NA, DATASHELF 9 100; installation instructions for
data sets are included in Section 
MITL9141-753-503-NA, DATASET
1100 Series and Section 
MITL9141-753-506-NA, DATASET 2100 Series.
Installation instructions for the Modem Interconnect Panel are...

Page 28

SECTION MITL9109-094-200-NAPage 20 

Page 29

Shipping, Receiving, and Installation Information
3. INSTALLATION REQUIREMENTSEnvironmental Requirements
3.01The SX-200 DIGITAL PABX equipment may be installed in any
location which is within the following temperature and humidity
ranges and fulfills the space requirements described in the next para-
graph.Temperature 
+I 0 to +4O”C (+50 to +104”F)
Relative Humidity 
20-80% (non-condensing)
Maximum Altitude 4000 meters.
Floor Space
3.02The minimum floor space for installation and subsequent main-tenance...

Page 30

SECTION MITL9109-094-200-NA
-near a reproducing or copying machine. A minimum clearance
of 3 m (10 
f-t) must be provided if the reproducing machine is
not equipped with a filtering system, and the room should be
ventilated by an exhaust fan.Power Supply Requirements
3.04The customer must provide one single-phase power receptacle
for each cabinet, as follows:
-Each cabinet should have its own 120 V, 60 Hz, 15 A branch
circuit.
-The power receptacle must be a 3-wire type, with the ground
wire connected to...
Start reading Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Related Manuals for Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

All Mitel manuals