Mitel SX 200 DIGITAL Pabx Shipping, Receiving, And Installation Information Manual

Shipping, Receiving, and Installation Information
SHELF GROUND+EDG-
DGSHELF GROUND
DG.
EDG
DGCABINET
GROUND STUD
UI/ IIBAY 6IIBAY-DG
-DG
LL;;I;;LF GROUND
IBAV 4
- SHELF GROUND
rO=Q TO FANS
I,FROM LINE FILTER
J!! !!!!‘,, ! DG
CABINET
i
_. .- .._.GROUND STUD
I
I
I)cAC POWER CABLES 
m-GROUND WIRES B
KA0657EZRZFigure 4-17 Rear View of 672-Port Peripheral Cabinet 
- Power and Grounding
Page 43 

SECTION MITL9109-094-200-NA
BAY
BAV
Ic)cl0. . . . . . . .d
El. . . . . . . .
ii ii ii ii::!: ii ii ii
. .
Y.j  
ii
. .......
........:
........
....... .. .. .. .. .
nJ0
cl
1 . . . . . . .
I/
cl
. . , . . . . .
. .::ii i;;;::. .. .:: ii ii :::: . .i:-BAY 7
LlLI IIPFT CARD
-PIT CARD
BAY 5
KAO655ElRlFigure 4-18 Rear View of 672-Port Peripheral Cabinet 
- PCM Signal Cables
Page 44 

Shipping, Receiving, and Installation Information
5. INSTALLATION CHARTS5.01Follow the Installation Charts, in sequence, to install an SX-200
DIGITAL PABX. Skip those charts for equipment that is not being
installed at this site.
5.02Section 
MITLS 109-094-2 1 0-NA, Customer Data Entry, describeshow to enter data 
Into the system to make it operational.
Installation Forms, Section 
MITL9109-094-206-NA, includes Tip and
Ring assignment forms for all card positions in the system.
Precautions5.03 When...

SECTION MITL9109-094-200-NASystem Configuration
5.06The System Configuration identifies all equipment that is part of
this installation, defines where each is located within the PABX,and to which circuit or equipment each is connected external to the
PABX. The Configuration also identifies the information that must be
programmed into the database to define this equipment to the proces-
sor. Refer to Section 
MITL9109-094-180-NA, Engineering Information,
for the configuration rules for the PABX.672 Port...

Shipping, Receiving, and Installation Information
Install Bay Power Supply cards into each Bay; at the rear of thecabinet, connect the ac power cords to each BPS.At the front of the cabinet, put on the antistatic wrist strap and install
the cards (except MCC and SMC); select the required options on trunkcards and other cards which have selectable options. Refer to Chart
5-22.
Install the Floppy Disk Drives into their slots in the Control Bay.
Install the Switch Matrix Card into its slot in the Control...

SECTION MITL9109-094-200-NACHART 5-2
UNPACK EQUIPMENT CABINETS AND EQUIPMENT EXCEPT PRINTED CIRCUIT BOARDS
stepActionComments
1.Cut and remove retaining straps.
2.Open and remove triwall cartons and otherRefer to Figure 5-l.
packing material.
3.Remove the cabinet from the shipping pallet.
4.Remove plastic sheet from cabinet.CAUTION: Do not open or
unpack any printed circuit board
cartons.
5.Unpack cartons and check contents againstRetain some packing material in
paging lists.case any items must be...

Shipping, Receiving, and Installation InformationWOODEN
PALLETSECURING
STRAPS
-1:‘TOP CAP
SHOCK-
ABSORBING
BOLSTERSLEEVE
/CABINET
SHOCK-
BASESHOCK-
ABSORBING
BASE
Figure 5-l Remove External Packaging
Page 
49 

SECTION MITL9109-094-200-NACHART 5-3 (CONT’D)
INSPECT EQUIPMENT
StepAction
Comments
14.Check that all cable connectors are seated
firmly and free from damage.
15.Visually inspect backplane for damage.
16.Close power supply door.
17.Tag defective items and continue. Fill in
relevant portion of Damage Report.
18.Repack tagged items and return according to
local procedures.
CHART 5-4
INSTALL CONTROL CABINET
Note:Ideally, a Control cabinet is installed beside a Peripheral cabinet (existing SX-200 
cabinet...

Shipping, Receiving, and Installation Information
CHART 5-5
VERIFY GROUND CONNECTIONStepActionComments
Before installation can begin, an insulated #6
AWG green ground wire must be connected
between the equipment location and an
approved ground (metallic cold water pipe or
equivalent where it enters building).
1.Before plugging any cards into the cabinet, orDo not power up the PABX.
connecting the Equipment Ground wire, ensure
the equipment circuit breakers are turned off.
2.Plug the AC line cord into the...

SECTION MITL9109-094-200-NACHART 5-6
INSTALL ANALOG PERIPHERAL CABINET
StepActionComments
1.Unpack the cabinet and other items, except
printed circuit cards. Check items received
against packing list.
2.Inspect the cabinet, shelf, and other items forEnsure that the doors open and
loose, missing, or damaged parts.close freely, and all cables are
secure and in place. Remove
shipping screws from rear door.
3.Place the peripheral cabinet beside of the
control cabinet.
4.Route PCM cable PN9 108-026-OOO-NA...